background image

PTSS 1200 B1

■ 

6 

GB

IE

NI

c)  

If you want to restart a saw that is still in the 
workpiece, centre the saw blade in the cut 
and check to ensure that the teeth are not 
caught anywhere in the workpiece.

 If the saw 

blade catches it can jump out of the workpiece 
or cause a kickback when the saw is restarted.

d)  

Support large panels or boards to reduce the 
risk of the saw blade jamming and causing 
a kickback.

 Large panels tend to bend under 

their own weight. Panels must be supported on 
both sides, in the vicinity of the saw cut and 
also at the edge.

e)  

Do not use blunt or damaged saw blades.

 

Saw blades with blunt or misaligned teeth may 
cause excessive friction as the saw cut is too 
narrow, and this can cause a saw blade jam 
and kickback.

f)  

Blade depth and bevel adjusting locking 
levers must be tight and secure before making 
cut.

 If the settings change while sawing, the 

saw blade might jam and cause a kickback.

g)  

Be particularly careful when sawing in 
existing walls or other obscured areas.

 The 

inserted saw blade could get caught on hidden 
objects and cause a kickback.

Function of the blade guard

a)  

Before every use, check to ensure that the 
blade guard closes properly. Do not use the 
saw if the blade guard does not move freely 
and does not close immediately. Never clamp 
or tie the blade guard into the open position.

 If 

the saw accidentally falls to the floor, the blade 
guard might bend. Ensure that the blade guard 
moves freely and does not touch the saw blade 
or other parts at all cutting angles or depths.

b)  

Check the operation of the blade guard 
spring If the guard and the spring are not op-
erating properly, have the appliance serviced 
before using it.

 Damaged parts, sticky deposits 

or accumulations of chippings can cause the 
blade guard to operate slowly.

c)  

When making a "plunge cut" which is not at  
right angles, secure the saw base plate to  
prevent any lateral movement.

 Lateral move-

ment can cause the saw blade to jam, thus 
causing a kickback.

d)  

Do not leave the saw on the work bench or 
floor if the blade guard is not fully covering 
the saw blade.

 An unprotected, coasting saw 

blade will move the saw in the opposite direc-
tion to the cutting direction and saw anything 
in its path. Be aware of the time it takes for the 
blade to stop after switch is released.

Supplementary notes

 

Do not use any grinding discs.

 

Use only saw blades with diameters corre-
sponding to the label on the saw.

  

WARNING! DANGER DUE TO DUST 
EXPOSURE!

 

When working for extended periods of time 
on wood and, in particular, materials that 
produce dust which is hazardous to health, 
connect the appliance to an appropriate 
external dust extraction appliance.

Wear protective gloves!

Wear a dust mask!

Wear safety goggles!

Wear ear protectors!

 

Do not allow the teeth of the saw blade to 
overheat.

 

When sawing plastic, avoid melting the plastic.

  

WARNING! TOXIC FUMES!

 

Working with the tool can produce harmful/
toxic dusts that represent a health hazard for 
the person operating the appliance and for 
any other people in the area.

 

Materials containing asbestos may not be pro-
cessed. Asbestos is a known carcinogen.

Summary of Contents for PTSS 1200 B1





























Reviews: