PEH 30 C3
■
8
│
GB
│
IE
│
NI
│
CY
Chamfering edges
The V grooves in the front plane sole allow
easy chamfering of workpiece edges .
♦
Use the V groove that corresponds to the
chamfer width required .
♦
Place the planer with the V groove onto the
workpiece edge and guide it forwards .
Using the rip fence
♦
To fit the rip fence, guide the connecting
screw
8b
through the connecting piece
8a
and
the rip fence .
♦
Place the washer
8c
on the connecting
screw
8b
.
♦
Screw the lock nut onto the connecting
screw
8b
.
♦
Fit the rip fence onto the appliance using
the fastening screw .
♦
Undo the lock nut and set the desired width .
♦
Retighten the lock nut .
♦
Ensure that the plane is applied with lateral
pressure .
Using the fold depth stop (see fig . G)
♦
Fit the fold depth stop onto the appliance
using the fastening screw .
♦
Set the desired fold depth in millimetres using
the fold depth stop .
♦
Repeat the planing process several times until
the required fold depth is achieved .
Removing/replacing the planing
blade (see figs . C–E)
WARNING! RISK OF INJURY!
►
Always remove the plug from the power
socket before working on the appliance .
CAUTION!
►
There is a risk of injury due to the cutting
edges of the planing blade !
►
Never touch the planing blade on its
cutting edges .
The planing blade has two cutting edges and
can be turned .
♦
Replace the planing blade
when both cutting
edges are blunt .
♦
Do not try to sharpen the planing blade
.
Turn the planing blade or replace it
WARNING! RISK OF INJURY!
►
Wear suitable protective gloves when changing
the planing blades .
NOTE
►
Do not undo the two hex socket screws .
These are used for adjusting the height of the
cutter block . No adjustment is required if you
use the planing blades sold by the manufac-
turer . Use only the planing knives supplied by
the manufacturer .
►
When changing the blade, always replace
both blades to prevent an imbalance .
►
Unscrew only one blade to start with . This will
allow you to use the factory-mounted second
blade for reference when reassembling later .
♦
Use the supplied open-ended spanner to
undo the 3 fastening screws a little way so
that the planing blade can be moved
(see fig . C) .
♦
Push the movable cutter block guard into the
slot in the housing .
Summary of Contents for PEH 30 C3
