GB/CY
9
▪
Never trigger the fastner driving tool into
empty space.
Following this instruction will
prevent danger due to uncontrolled flying faste-
ners and overloading the device.
▪
Before transporting, disconnect the faste-
ner driving tool from the compressed air
network, particularly when using ladders
or are moving with an unaccustomed body
posture.
▪
At the workplace, only carry the fastener
driving tool by its grip and never with the
trigger actuated.
▪
Pay attention to workplace conditions.
Fasteners may strike completely through thin
workpieces or slide off corners or edges to cause
a danger to persons.
▪
Use suitable personal protection
equipment, e.g. hearing and eye
protection.
Wearing personal protec-
tive devices such as dust mask, non-slip
safety shoes, safety helmet or hearing
protectors, depending on the type of
fastener driving tool and its application,
reduces the risk of injuries.
Additional safety information for
compressed air tackers
▪
RISK OF INJURY!
Never exceed the maximum permissible
operating pressure of 8 bar. Use a pressure
reducer to adjust the operating pressure.
▪
RISK OF INJURY!
Never use oxygen or other flam-
mable gases as energy source.
▪
Keep your working area clean and well lit.
Untidy or poorly lit working areas can lead to
accidents.
▪
Keep children and other individuals away
from the fastener driving tool during use.
Distractions can cause you to lose control of the
device.
▪
Remain alert at all times, watch what you
are doing and always proceed with cau-
tion when working with a fastener driving
tool. Do not use any fastener driving tool
if you are tired or under the influence of
drugs, alcohol or medication.
One moment
of carelessness when using the fastener driving
tool may result in serious injuries.
▪
Avoid placing your body in an unnatural
position. Keep proper footing and balance
at all times.
By doing this you will be in a bet-
ter position to control the fastener driving tool in
unforeseen circumstances.
▪
Before any repair and maintenance work or
transport, remove the device from the compres-
sed air source.
Additional safety information for
the protective goggles
▪
The protective goggles are designed for use with
the air stapler/nailer and only within its scope of
intended use.
▪
The protective goggles provide sufficient protection
against particles of up to 6 mm in diameter at a
speed of up to 45 m/s.
▪
Replace the protective goggles as soon as the
oculars are scratched or damaged.
▪
If you replace the protective goggles, be sure to
use protective goggles with the same protective
properties.
▪
Materials which may come in contact with the
wearer’s skin could cause allergic reactions to
susceptible individuals.
▪
Protective goggles can represent a hazard for
the wearer if it is worn over normal corrective
glasses due to the impact from particles.
Declaration of the markings of the protective
goggles:
GUOTAI
Marking of the manufacturer
166
Number of the EU testing standard
for the protective goggles
1
Optical class
F
Protection against impacts from
lower energy
CE
CE label
ANSI/ISEA
Z 87.1-2010 Number of the ANSI standard for the
protective goggles
Summary of Contents for PDT 40 E4
