
21
GB/IE/NI
Wearing parts*: Spark plug, air filter, thread coil, blade, saw chain,
chain blade
* may not be included in the scope of supply!
m
Warning!
Only use original spare parts and accessories from the manufacturer.
Failure to do so can reduce performance, result in injuries and void your
warranty.
Important note in the case of repairs:
When returning the device for repair, please ensure for safety reasons
that it is free of oil and petrol when it is sent to the service centre.
Ordering spare parts
Please provide the following information when ordering spare parts;
• Device type
• Device article number
Spare parts / accessories
You can always use the protective devices supplied with the machine for
the cutting accessories listed here.
•
Brush cutter / grass trimmer:
Line coil Ø 450
7910700707
TRICORD line coil Ø 450
7910702702
Thread coil TRICORD Ø 2,8 mm x 4 m
7910702704
3 tooth blade Ø 255 x1,4
7910700702
Transport protection for 3 tooth blade
3904801065
4 tooth blade Ø 255 x 1.5
7910700705
Transport protection for 4 tooth blade
3904801066
8 tooth blade Ø 255 x 1.5
7910700711
Transport protection for 8 tooth blade
3904801066
Protective shield grass trimmer
3904803034
•
Pole pruner:
Saw chain 3/8.50-39
7910100732
Guide rail AL10-39-507P
7910100731
Transport protection for chain
3904801039
Extension for pole-mounted pruner
7910700710
•
Hedge trimmer:
Hedge trimmer blade 400 mm
7910700703
Transport protection for 400 mm blade
3904801043
15. Cleaning and storage
15.1 Cleaning
• Keep the handles free of oil so that you always have a secure grip.
• If necessary, clean the device with a damp cloth and, if necessary, with
a mild flushing liquid.
m
Attention!
• Disconnect the spark plug connector before cleaning.
• Never immerse the device in water or other liquids for cleaning.
• Store the device in a secure and dry place and out of reach of chil-
dren.
15.2 Storage
Clean and maintain the device before storing it.
Caution:
Never stow the device for longer than 30 days without carrying out the
following steps:
Stowing the device for more than 30 days
If you stow the device for longer than 30 days, it must be prepared
ahead of time. Otherwise, the remaining fuel in the carburettor will evap-
orate and leave a rubbery sediment behind. This could make it difficult to
start and result in expensive repair work.
• Drain the fuel (see 10.3.1)
• Start the engine and let it run until it stops in order to remove the fuel
from the carburettor.
• Allow the engine to cool down (approx. 5 minutes).
• Remove the spark plug (see 14.2.1).
• Add 1 teaspoon of clean 2-stroke oil to the combustion chamber.
• Pull the starter cord slowly several times to coat the internal compo-
nents.
• Re-insert the spark plug (see 14.2.1).
Note:
Store the device in a dry location, far away from potential sources of
ignition, such as furnaces, hot water boilers with gas, gas dryers, etc.
15.3 Re-commissioning after a long storage period
• Remove the spark plug (see 14.2.1).
• Pull the starter cord quickly to remove excess oil from the combustion
chamber.
• Cleaning the spark plug and make sure that the electrode gap on
the spark plug is correct. Or insert a new spark plug with the correct
electrode gap.
• Re-insert the spark plug (see 14.2.1).
• Prepare the device for operation.
16. Disposal and recycling
The device is supplied in packaging to avoid transport damages. This
packaging is raw material and can thus be used again or can be reinte-
grated into the raw material cycle.
The device and its accessories are made of different materials, such as
metals and plastics. Take defective components to special waste disposal
sites. Check with your specialist dealer or municipal administration!
The packaging is wholly composed of environmentally-
friendly materials that can be disposed of at a local recy-
cling centre.
Contact your local refuse disposal authority for more de-
tails of how to dispose of your worn-out electrical devices.
Fuels and oils
Fuel residues, oils and liquids used for cleaning must be disposed of in an
environmentally friendly manner!
Empty oil and fuel tanks must be disposed of in an environmentally friend-
ly manner.
Dispose of liquids and containers at appropriate collection centres.
Summary of Contents for PBK 4 B3
