PHDB 4 B2
■
12
│
GB
│
IE
│
NI
Self-priming from open tanks/containers and
natural water sources
Use the self-priming equipment supplied.
–
Intake filter
–
3 m reinforced suction hose
With this accessory the appliance can draw water to max. 1 m above the
water surface. This can take up to 1 minute.
♦
Immerse the 3 m suction hose completely underwater to get the air
out.
♦
Connect the suction hose to the appliance and ensure that the
intake filter remains underwater.
♦
Run the appliance without the hand spray gun attached until water
flows evenly out of the high-pressure hose .
If no water flows out after 1 minute, switch the appliance off and
check the appliance. Once the water flows, switch off the appliance
and attach the hand spray gun and the jet pipe so you can
work.
■
It is important that the hose and coupling are of a good quality, tightly
fitted and that the seals are undamaged and inserted straight. Leaky
connections can impair the suction.
Bleeding the appliance
♦
Remove the nozzle .
♦
Start the engine (see "Starting the engine").
♦
Pull the trigger on the hand spray gun several times.
♦
Allow the appliance to run until the water comes out of the jet pipe
without any air bubbles.
♦
Switch off the appliance and screw the nozzle back on.
Use
WARNING!
►
Switch off the appliance before making any adjustments or carrying
out maintenance work.
DANGER! RISK OF EXPLOSION! DO NOT SPRAY
FLAMMABLE LIQUIDS!
►
Place the appliance on a firm surface.
►
The high-pressure cleaner may not be operated by children.
(Risk of accidents due to improper use of the appliance).
►
The appliance generates a lot of noise.
Risk of hearing damage. Always wear suitable hearing protect when
working with the appliance.
►
The water jet coming out of the high-pressure nozzle exerts recoil
force on the gun. An angled jet pipe can also cause torque.
Therefore, hold the jet pipe and gun firmly in your hands.
►
Never aim the water jet at people, animals, the appliance itself or
electrical components.
►
Vehicle tyres/tyre valves may only be cleaned at a minimum spray
distance of 30 cm. Otherwise the vehicle tyres/tyre valves could
be damaged by the high-pressure jet. The first sign of damage is a
discolouration of the tyre. Damaged vehicle tyres are a source of
danger.
►
Materials containing asbestos or other substances that are harmful to
health may not be sprayed.
►
To protect the operator from water spray, wear suitable protective
clothing.
►
Always ensure that all hose connection are screwed tight.
►
The trigger of the hand spray gun must not be jammed during use.
Filling oil/petrol
♦
When you use the appliance for the first time, unscrew the red oil inlet
screw and add approx. 0.6 l engine oil (15W40). Use the funnel
to do this.
♦
Unscrew the filler cap and add standard commercial lead-free
petrol to the fuel tank . The tank has a maximum capacity of 3.6 l.
Add fuel up to the red mark.
Starting the engine
CAUTION!
►
Before first use, add engine oil (15W40, approx. 0.6 l) and fuel
(regular unleaded petrol).
♦
Check the fuel and oil levels; top up as necessary.
♦
Provide adequate ventilation for the appliance.
♦
Ensure that the spark plug/spark plug connector are firmly fitted.
CAUTION!
►
When starting using the pull starter there can be a kickback that
can cause injuries to your hand.
■
Wear protective gloves when starting.
♦
Open the fuel tap ; to do this, move the fuel tap to the "ON"
position.
♦
Move the On/Off switch to the "ON" position.
♦
Set the choke to position I
\
I (in the left position).
