PHDB 4 B2
GB
│
IE
│
NI
│
11
■
Fitting the hand spray gun, the jet pipe and the
nozzle
DANGER!
►
Risk of injury! Appliance, supply pipes, high-pressure hose and
connections must be in perfect working order. If the equipment is
not in perfect working order, the appliance may no longer be used.
♦
Connect the jet pipe to the hand spray gun .
♦
Tighten the screws of the jet pipe by hand.
♦
Fit the nozzle onto the jet pipe . Ensure that it clicks into place
correctly.
♦
Fit the high-pressure hose onto the hand spray gun .
Operation
Checking the oil level of the engine
■
Check the oil level before each use.
■
Do not use the appliance if there is no oil visible on the dipstick .
■
Add oil as required. Use only engine oil (15W40).
♦
Place the appliance on a flat, level surface and remove all dirt from
around the oil inlet/dipstick .
♦
Use the dipstick to measure the oil level.
Unscrew the dipstick and wipe it clean with a cloth.
Put the dipstick back into the oil inlet without screwing it in.
Pull the dipstick back out and check the oil level.
♦
Check that the oil level is somewhere between the minimum and max-
imum levels (marked as L for low and H for high on the dipstick ).
♦
To fill up the oil, take the supplied funnel and pour the oil slowly
into the oil inlet . Do not overfill!
♦
Wait a minute until the oil has settled before measuring the oil level
again as described above.
♦
Screw the dipstick back into the oil inlet.
CAUTION!
►
Do not overfill the oil. A too high oil level can cause engine damage.
The maximum fill level for the tank is 0.6 litres.
NOTE
►
The engine is equipped with an oil level sensor. The oil level sensor
switches the engine off if the oil level is too low and prevents a
restart. If the engine cuts out although the oil level is correct, check
whether the petrol-powered high-pressure cleaner is standing straight.
Bleeding the oil tank
CAUTION!
►
Before first use, the bleed valve on the oil tank needs to be replaced.
On delivery, a black transport oil plug is screwed in which has to
be replaced by the supplied red oil plug .
Engine
Observe the section "Safety instructions"!
■
Before use, read the manufacturer's operating instructions and pay
close attention to the safety instructions.
■
Checking the oil level of the engine.
Do not use the appliance if the oil level has fallen below "MIN".
■
Add oil as required.
■
Fill the fuel tank with unleaded petrol.
Do not use a 2-stroke mixture.
Adding fuel
DANGER! RISK OF FIRE AND EXPLOSION!
►
Never refuel in confined spaces or when the engine is running
or still hot.
►
Do not smoke while refuelling.
►
Do not use any 2-stroke mixture.
►
Do not refuel in the vicinity of open flames or sparks.
►
Do not spill fuel – use a funnel.
►
Wipe up any spilt fuel.
►
After refuelling, close the fuel canister and the tank properly.
♦
Fill the fuel tank with unleaded petrol.
♦
Add fuel up to the red mark.
Water connection
See technical specifications for the connection data.
■
Connect the supply hose (minimum length 7.5 m, minimum diameter
3/4") to the water connection on the appliance and to the water
supply (e.g. tap).
■
Turn on the water supply.
NOTE
►
The water supply hose is not included in the delivery.
Drawing water out of a container
DANGER!
►
Never draw water from a drinking water container.
Never prime with liquids containing solvents such as paint thinners,
petrol or oil. Atomised spray from solvent is highly flammable,
explosive and toxic.
♦
Connect the suction hose (diameter at least 3/4") with the filter
(accessories) to the water connection .
MIN.
MAX.
