Parker SciLog FilterTec Plus Installation, Operation & Maintenance Instructions Manual Download | Manualshive

Page: 4 / 72

background image

4

Précautions

LISEZ ce manuel AVANT de faire fonctionner ou d’entretenir cet équipement.

SUIVEZ attentivement ces instructions.

CONSERVEZ ce manuel pour future référence.

NE LAISSEZ PAS du personnel non qualifié utiliser, nettoyer, inspecter, entretenir, réparer
ou manipuler cet équipement.

DÉBRANCHEZ TOUJOURS cet équipement de la source de courant avant de nettoyer ou

d’exécuter l’entretien.

APPELEZ PARKER pour pièces détachées, renseignements et entretien.

SI le cordon d'alimentation est perdu ou endommagé, contactez le service clientèle pour
en obtenir un nouveau. Ne le remplacez pas par vous-même.

ATTENTION

DÉBRANCHEZ TOUT COURANT DE CETTE UNITÉ AVANT DE FAIRE
L’INSTALLATION, D’EFFECTUER L’ENTRETIEN, LE NETTOYAGE OU
AVANT DE RETIRER LE FUSIBLE. NE PAS OBSERVER CES
PRÉCAUTIONS RISQUERAIT DE CAUSER DES BLESSURES
CORPORELLES OU/ET D’ENDOMMAGER L’ÉQUIPEMENT.

PRUDENCE

SOYEZ PRUDENT LORSQUE VOUS MANIPULEZ DES APPAREILS
SENSIBLES À L’ÉLECTROSTATIQUE.

ATTENTION

AUTORISEZ SEULEMENT LE PERSONNEL QUALIFIÉ À
ENTRETENIR CET ÉQUIPEMENT. SOYEZ PRUDENT LROSQUE DES
VÉRIFICATIONS, TESTS ET AJUSTEMENTS DOIVENT ÊTRE
EFFECTUÉS SOUS TENSIONS. NE PAS OBSERVER CES
PRÉCAUTIONS RISQUERAIT DE CAUSER DES BLESSURES
CORPORELLES.

ATTENTION

POUR ASSURER UNE PROTECTION CONTINUE CONTRE UNE
DÉCHARGE ÉLECTRIQUE, BRANCHEZ UNIQUEMENT SUR UNE
PRISE CORRECTEMENT RELIÉE Á LA TERRE. NE RETIREZ PAS LA
FICHE DE TERRE.

SI LE CORDON D'ALIMENTATION EST PERDU OU ENDOMMAGE, CONTACTEZ LE
SERVICE CLIENTELE POUR EN OBTENIR UN NOUVEAU. NE LE REMPLACEZ PAS PAR
VOUS-MEME.

«
...
2
3
4
5
6
...
»

Summary of Contents for SciLog FilterTec Plus









































































Reviews:

No comments

Related manuals for SciLog FilterTec Plus

Brand: Omnia Pages: 8

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

Brand: Vahle Pages: 96

ECL Comfort 210

Brand: Danfoss Pages: 28

Lab companion SI-300

Brand: Jeio tech Pages: 69

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 4

Brand: Jct Pages: 16

Brand: lancer Pages: 3

Brand: lancer Pages: 12

Brand: R2 Pages: 26

Brand: Malekko Pages: 2

Brand: Major Pages: 26

Brand: Yamaha Pages: 126

DM 2000 Version 2

Brand: Yamaha Pages: 8

Brand: Ultrasonic Pages: 33

Brand: mychway Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands