background image

4601503-P1V-S Issue 5

Disconnect air and electrical supplies before 
attempting repair or maintenance.
See ISO 4414-1982 for safety requirements covering 
the installation and use of pneumatic equipment.

Koppla ifrån luft och elektriska anslutningar innan 
reparations-och underhållsarbeten påbörjas.
Se ISO 4414-1982 för säkerhetsbestämmelser
täckande installation och användning av pneumatisk 
utrustning.

NOTICE ALL DOCUMENTATION!

Before beginning work this operating instruction
booklet has to be read through carefully. Always follow
the instructions during operation. Give this operating
instruction booklet to the operator.

1. Important Notes

The safety and warning instructions contained 
should always be followed!

Safety and Warning Signs

IMMEDIATE DANGER

Possible consequences: death or grave injuries.

DANGEROUS SITUATION

Possible consequences: slight or minor injuries.

DAMAGING DANGER

Possible consequences: damage to drive or the
surrounding area.

Important instructions relating to explosion
protection.

Application tips and other useful information.

Definition

Potentially explosive atmosphere (hereinafter referred to as 
“Ex-area”)
= An atmosphere which could become explosive due to 
local and operational conditions.
The observance of the operating instructions is the 
precondition for an error free operation and the fulfillment 
of warranty claims. Therefore, please read the operating 
instruction booklet prior to working with the air motor!  
The operating instruction booklet contains important tips 
for motor service and should therefore be kept in the 
vicinity of the motor.

Disposal

Always observe the most current regulations for 
disposal.

Especially during installation, repair or maintenance water 
damaging agents, such as:
•  lubricating greases and oil
•  hydraulic fluid
•  cooling agents
•  solvent-containing cleaning agents may not leak into  
  the ground or into the sewage system!
Such materials must be stored, transported, contained 
and recycled in suitable containers.
Housing parts, tooth rings, shafts, as well as gear parts 
should be disposed off as steel scrap.

Summary of Contents for P1V-S

















Reviews: