background image

MT-700 series installer guide 

 

 Page 3 

 

WARNING

: Read this Manual before operation 

Use this product only for its intended use as described in this manual. Do not use any other 
connection methods that are not recommended by the manufacturer.

 

Introduction 

This manual is intended for the installer of the product. He or she must be a skilled technician with a 
minimum of installation knowlwdge with Micro Thermo or Echelon product. 
The end user will never have to move, connect or disconnect physical part of the product. 
The U700 is a monitoring industrial controller, one of the multiple combinaison of the new Micro 
Thermo Technologies MT-700 product family. 
It is made of a main MT-722A Controller (A may be another letter) and a MT-716U (16 universal input) 
expension module. 

U700 Installation 

Mounting 

The U700 Monitoring Node has two mounting options: DIN rail; or Direct Mounting by the eight screw 
holes (four per controller module). 

For DIN rail mounting

, mount the DIN rail in the desired location and attach the two controller modules 

to the rail separately.  First install the MT-722A controller at the left end of the DIN rail. You may need to 
pull the locker up with a flat screw driver. Then put the MT-716U beside the Controller. Ensure the 
controllers

’ communica

tion ports are correctly aligned, and 

gently slide the units together until the plastic housings are 
flush. 

For Direct Mounting,

 mount the controller modules separately, 

remove all wire connectors before securing the MT-722A 
module in the left place using (4) #6 screws.  Align the 

controllers’ communication ports, and push the 

MT-716U units 

together until the plastic housings are flush.  Secure the second 
module in place using (4) #6 screws. Replace wire connectors. 
 
Any combinason of MT-700 modules can be made as long as only one MT-722A is used per row and 
placed at the left most of the row. 

If the MT-722A is loaded with a battery cell or if any relay of a of 

MT-700 module is used to control voltage higher than 24V the entire row should be housed in an 
electrical enclosure. 

 
 

 

Summary of Contents for MT-700 Series























Reviews: