background image

 2

Operation

2     Precautions

Instruction book, IQAN- G12

2

Precautions

Work on the hydraulics control electronics may only be carried out by trained 

personnel who are well-acquainted with the control system, the machine and its safety 

regulations.

W

ARNING

Make sure that you have sufficient knowledge before designing, modifiying or 

servicing the control system. 
Read the relevant sections of this document before conducting any work on the control 

system.

W

ARNING

This product is not field repairable.

N

OTICE

As much as possible of the welding work on the chassis should be done before the 

installation of the system. If welding has to be done afterwards, the electrical 

connections on the system must be disconnected from other equipment. The negative 

cable must always be disconnected from the battery before disconnecting the positive 

cable. The ground wire of the welder shall be positioned as close as possible to the 

place of the welding. The cables on the welding unit shall never be placed near the 

electrical wires of the control system. 

Operation

IQAN-G12 receives and transmits radio frequency energy while switched on. 
Follow any special regulations and always switch off the IQAN-G12 wherever 

forbidden, or when you suspect that it may cause interference or danger.

Disposal

Observe your local/national regulations when disposing the device and its package.

Start-up, maintenance, and diagnostics

For all personnel carrying out installation, commissioning, maintenance or 

troubleshooting. 

W

ARNING

Work on the hydraulics control electronics may only be carried out by trained 

personnel who are well-acquainted with the control system, the machine and its safety 

regulations.

Before you start, 

Read section "Start-up", on page 15.

Additional information for service

Mounting and maintenance instruction book.

Summary of Contents for IQAN-G12





































Reviews: