manualshive.com logo in svg

Parker HAUSER HPLA Series, User Manual

Share
Download
Parker HAUSER HPLA Series User Manual Download Page 46

Mounting / Repair                 

    PLEASE NOTE: THIS IS HAUSER GERMANY MANUAL. 

                                                                             FOR USA NOMENCLATURE PLEASE GOTO PARKERMOTION.COM

 

 

46 

7.  Move the carriage for approximately 10 strokes over the whole length at a low speed 

(v < 2  m/s). Watch the steel strip to see whether a "wave" forms in front of the respective 
turning station in the direction of movement. 

8.  Then stop the carriage coming from the drive station (20) at 0.5m before the tensioning 

station (2). 

9.  Unfasten steel strip fixing screw (9) in cover of tensioning station. 
10.  Smooth out the "wave", but do not strain the strip in doing so. 
11.  Tighten the screw. 

5.11.1.3  Replacing the steel strip 

 

Note

 

New steel strips must only be obtained from Parker. 
To order one, we will need to know the length L of 
the profile. 

Using these details, the steel strip will be shortened 
and pierced with two fastening holes. 

L

B

1.  Dismantle the steel strip (see chapter 5.11.1.1). 
2.  Remove clamping piece from drive station. With the HPLA180 and HPLA120, pull steel strip 

off grooved drive stud. With the HPLA80, simply unfasten clamping plate (see Figure on 
page 48). 

3.  With a HPLA180 or HPLA120, connect new steel strip with grooved drive stud. 
4.  Secure clamping piece, and/or with the HPLA80 fix steel strip with clamping plate. 
5.  Mount the steel strip (chapter 5.11.1.2). 

5.11.1.4 Replacing 

the 

drag bar (felt wiper) 

616

615

614

 

1.  Switch off the actuator at the main switch. 
2.  Dismantle the strip guides (5) on both sides of the load 

attachment plate. 

3.  Replace the felt wiper (617) with a new one. Make sure 

that the springs (616) do not fall out. 

4.  The strip guides (5) on both sides of the load attachment 

plate must be joined securely at the sides and the top. 

5.  Switch on the actuator drive. 

5.11.1.5  Replacing the baffle or running bar 

611

601

608

607

 

 

1.  Dismantle the steel strip (see chapter 5.11.1.1) 
2.  Push out the old baffles (611) to the side. 
3.  Push new baffles in the load attachment plate (601) so that the steel strip runs over the 

radius of the baffle. Align the baffle in the centre. 

4.  Mount the steel strip (see chapter 5.11.1.2) 

Pos. 5 

Summary of Contents for HAUSER HPLA Series
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands