background image

  

 

TROUBLE SHOOTING 

 

A.

 

Red LED on Infrared Head Unit “A” is illuminated. (Infrared Head Units are not paired 
properly. 

 

1.

 

Check to see it both Infrared Head Units are mounted identically with the same height 
and clearance measurements. 

2.

 

Check for obstructions that are blocking the path of the beam. 

3.

 

Check the appearance of the lenses on both Infrared Head Units. If necessary clean by 
wiping with a soft, damp cloth. 

4.

 

Remove and re-install the batteries in both Infrared Head Units. 

5.

 

Install new batteries in both Infrared Head Units. 

6.

 

If the Red LED is still on after trying steps 1, 2, 3 and 4, call Customer Service. 

 

B.

 

Green LED on top of either Infrared Head Unit does not flash every 15 seconds or the Red 
LED on Infrared Head Unit “A” is not illuminated. 

 

1.

 

Batteries are fully discharged or batteries are not properly installed. 

2.

 

If the Green LED is still not flashing after trying step 1, call Customer Service. 

 
C.

 

The LED on the top of one or both Infrared Head Units flashes RED every 5 seconds. 

 

1.

 

Low Battery power. Replace batteries immediately. 

2.

 

Check to see if the batteries are in the proper position. 

 
D.

 

Garage door opener malfunctions after installing the Park-Daddy®. 

 

Although a very rare occurrence, the Park-Daddy

® 

could interfere with the garage door 

safety sensors causing a malfunction. Swap Infrared Head Unit A with Infrared Head Unit B 
and vice versa. This procedure should stop any interference. 

 

E.

 

No color illuminating from the status indicator and no tone on the RF Radio Receiver. 

 

1.

 

Make sure your ignition switch in your car is turned on. 

2.

 

Check to see if you have power to the DC cigarette lighter port. If not, check the fuse in 
your car. 

3.

 

Check the fuse in the RF Radio Receiver by unscrewing the tip of the bottom portion of 
the RF Radio Receiver. 

4.

 

Perform a hard reset by unplugging the RF Radio Receivers from the DC ports, remove 
and re-install the batteries in both Infrared Head Units. 

5.

 

Refer to RESTORING FACTORY CHANNEL SETTINGS section on page 12. 

6.

 

If steps 1, 2, 3, 4, and 5 did not correct the problem, call Customer Service. 

 

Summary of Contents for PDY-50-AA























Reviews: