Omix-Ada 11704.05 Owner'S Manual Download

Page: 1 / 6

460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]

Roof Top Tent

OMIX-ADA

TECHNICAL SUPPORT

PHONE:

M-F 8am - 5pm EST 1-800-449-6649 |

EMAIL:

[email protected]

FOR WARRANTY INFORMATION VISIT:

www.Omix-Ada.com

Components

Page 1/

Part # 11704.05

Window Rod..................................................(8)

3. Aluminum Rails..............................................(2)

Ladder Mounting Bracket............................(2)

5. Ladder............................................................(1)

6. Slide Plate......................................................(8)

7. Base Plate......................................................(4)

M8 x 55mm Bolt.............................................(8)

9. M8 Flat Washer..............................................(8)

M8 Nylock Nut...............................................(8)

11. M6 x 40mm Hex Bolt......................................(8)

12. M6 x 18mm Hex Bolt.......................................(2)

13. M6 Flat Washer..............................................(16)

14. M6 Nylock Nut...............................................(10)

15. M6 Plastic Washer..........................................(4)

16. Shoe Bag........................................................(1)

17. Tent Cover......................................................(1)

1. Roof Top Tent................................................(1)

This Roof Top Tent is designed to mount on most OE and aftermarket roof rack/crossbar systems.

Consult your

owner's manual for weight restrictions.

lace tent and tent base with holes face up on a clean, protected surface. Slightly open up tent, open up

entrance and remove all parts from the interior of the

tent.

Direction of Opening

Before you fit your new Roof Top Tent to your vehicle,

determine which side of the vehicle you want your tent to

open.

Read instructions thoroughly before assembling and installing this product. Product may vary from image.

Periodically check torque of all hardware.

Summary of Contents for 11704.05







Search results

Summary of Contents for 11704.05

Reviews:

Related manuals for 11704.05

Brands by name

Popular brands

Omix-Ada 11704.05, Owner'S Manual

Search results

Summary of Contents for 11704.05

Reviews:

Related manuals for 11704.05

Brands by name

Popular brands