background image

  

 

 

 

Do not modify this product in any way. Doing so will void the warranty. 
 

 

This product is designed to be used on flat, level, and hard surfaces. Using this product 
on surfaces other than those described above may create difficulty when trying to pair 
the Infrared Head Units.  

 

 

For disposal of batteries, follow the battery manufactures’ guidelines for proper 
disposal. 

 

 

Never dispose of any batteries in fire because they could explode. 
 

 

Always replace batteries immediately when the LEDs on the top of the Infrared Head 
Units flash RED indicating low battery voltage. 

 

 

Do not attempt to park more than one vehicle at the same time using a single system or 
multiple systems. 

 

 

Although a very rare occurrence, infrared signals emitted from the Park-Daddy can 
cause interference to the garage door opener safety sensors. Be sure to check the 
functionality for the garage door safety sensors after installation. Always check to be 
sure the garage door opener safety sensors are functioning properly before use. 

 

PRODUCT CARE 

 

To avoid damage to the optic lenses, clean by wiping with a soft, damp 
cloth. Do not use abrasives, harsh cleaners or chemicals to clean any 
part of the product. If any part of the product becomes wet, wipe off 
immediately with a soft, absorbent cloth. Do not submerge this product 
in any liquid or clean with running water. 
 

 

Summary of Contents for PDY-50-AA























Reviews: