background image

CONNECTING A SURROUND CONTROLLER 
TO THE UNBALANCED INPUTS ON YOUR A 52

4

Ch 1-5 Unbalanced Inputs

Use these inputs if your surround controller doesn’t have balanced output connectors or if you
simply prefer to use unbalanced connections. 

What You’ll Need:

Five shielded interconnect cables with RCA plugs

A surround controller with five RCA output jacks

Before Connecting

Leave the AC cord on the A 52 disconnected until you have made all other connections 
to prevent any surprise burst of sound.

Make sure that all your cables are long enough so they are not pulled or stretched 
once they are connected.

Make sure the 

Balanced-Unbalanced Inputs

selector switch on the A 52 is in its 

Unbalanced

(lower) position and the 

Ground

switch is in its 

Normal

(lower) position.

To Connect

1

Plug one end of the cable into the 

Unbalanced Ch 1 Input

jack on the A 52.

2

Plug the other end of the cable into the unbalanced output jack for the channel 
on your surround controller that you wish to correspond to Ch 1 on your A 52. 

3

– 

0

Repeat steps 1 and 2 for 

Ch 2, Ch 3, Ch 4, and Ch 5

.

YOU SHOULD KNOW

Write Down Your Connections  

Make a note of which channel on your surround controller now connects to each channel
of the A 52 so you’ll always hear the channels in their intended position and to facilitate
trouble-shooting in case you encounter a problem later on.

SURROUNDŁ

CONTROLLER

OUTPUTS

2

4

6

8

10

Ch 1

Ch 2

Ch 3

Ch 4

Ch 5

Input

Balanced

Unbalanced

Input

Balanced

Unbalanced

Input

Balanced

Unbalanced

Input

Balanced

Unbalanced

Input

Balanced

Unbalanced

Man

Balanced

Inputs

Unbalanced

Input

12 V

Output

Audio

Sensitivity

50  mV  250

Ground

Normal

Lift

WARNING

To Prevent Fire Or Shock Hazard,

Do Not Expose This Unit To Rain

Or Moisture.

Fuse

T15A/250V1-115V Area

T8A/250V-230V Area

AC 115V      60Hz
AC 230V      50Hz

Power Consumption: 1350W

Parasound Products, Inc.

San Francisco, CA USA

Manufactured under

license from Lucasfilm

Ltd. Lucasfilm and THX

are registered Trademarks

of Lucasfilm Ltd.

CAUTION

To Prevent Electric Shock, Do Not

Remove Cover. No User-Serviceable

Parts Inside, Refer Servicing  To

Qualified Service Personnel.

Auto Turn  On

L U C A S F

I

L M

L M

1

3

5

7

9

Ground Switch, 
set to down position

Inputs Switch, 
set to down position

RCA Plugs

Summary of Contents for Halo A 52






















Reviews: