Paragon P7 Installation & Maintenance Instructions Manual Download Page 5

LT6757 ( Iss 1 06/14 )

 

 

 

P7  Users Instructions

 

SECTION ONE Operating Appliance

 

 

Before  attempting  to  operate  the  appliance  check 
that  nothing  has  been  placed  in  front  of  the 
appliance that may interfere with the remote sensor 
operation. 

 

To light the appliance using the remote hand set: 

 
a.  Point  the  remote  control  hand  set  in  the  direction  of 

the  appliance  and  simultaneously  press  the  buttons 
marked  ‘   off’  and  ‘standby’.  Continue  to  hold  in 
these  two 

buttons  until  a  ‘bleep’  is  heard 

(approximately  2-3  sec.)  and  then  release  these 
buttons.  The  appliance  will  automatically  go  through 
the ignition sequence producing and the pilot should 
ignite.  Once  the  pilot  is  alight  the  appliance  will 
automatically  go  to  the  high  setting  (approximately 
20-25sec).  If  the  ignitor  stops  sparking  and  the  pilot 
fails to light, repeat this procedure.                                                

b.  If  the  ignitor  stops  sparking  and  the  pilot  fails  to  light  press  the 

'

'

  button  before  repeating  this 

procedure. 

c.  The appliance can be adjusted up or down by pressing the 

appropriate button 

'

'

 (low setting) or  

'

(high setting). These buttons have a duel function. If 

they  are  pressed  until  a  ‘bleep’  is  heard  and  then  released  immediately  the  appliance  will 

automatically go to the maximum 

'

'

 or minimum settings 

'

. On the other hand if the button is 

not  released,  gradual  adjustment  is  made  until  the  button  is  released  or  until  the  maximum  or 
minimum setting is reached.  

d.  To switch off the appliance press the 

'

'

 button or if the appliance is to be switch off for a short 

period it is recommended that the ‘standby’ button be used. This switches the main burner off but 
leaves the pilot on and will extend battery life. 

e. 

 

The appliance can be switch off without using the hand set by removing the appliance batteries 

located  behind  the  ash  pan  cover.  When  the  batteries  are  removed  there  will  be  a  delay  (up 
3minutes) after which double bleeps may be heard and shortly after the appliance will extinguish. 
Ensure that the battery is reconnect once the fire as been extinguished. The appliance cannot be 
operated without the use of the handset. 

 

 

NOTE: If the fire is extinguished for any reason wait 3 minutes before relighting. 

Summary of Contents for P7





























Reviews: