![background image](http://html1.mh-extra.com/html/paradyne/hotwire-8610-dslam/hotwire-8610-dslam_installation-manual_754032022.webp)
2. Installation
2-6
April 2001
8610-A2-GN20-10
Interconnecting 8610 Systems
Procedure
To interconnect multiple Hotwire 8610 systems:
1. Connect the end of an 8-pin modular cable into the Management OUT port of
the base chassis.
2. Dress the 8-pin modular cable to the left and under the chassis, behind the
foot, and up the side of the unit.
3. Plug the other end of the 8-pin modular cable into the Management IN port of
the 8610 chassis above, dressing the cable as in the previous step.
4. Repeat for the next 8610 chassis, connecting the Management OUT port of
Chassis 2 to the Management IN port of Chassis 3.
NOTE:
Bus cables must use Unshielded Twisted Pair (UTP) CAT5 cable. The total bus
cabling should not exceed 25 feet.
The following illustration shows the designated number for each DSL card slot in a
stack.
NOTE:
This illustration shows a stack of six Hotwire 8610 systems, which is valid for
rack mounting. However, the same relationship of software-assigned slot
numbers applies to two stacks of three each, mounted on a desk or tabletop
and connected by a bus cable. The base chassis must still have the MCP card
in physical Slot 1 with the base chassis Stack Position switch set to 1. The
software does not assign a slot number to the MCP card.
00-16313-02
DSL
Cards
MCP
Card
Assigned DSL Slot Numbers
Additional
Systems
Base
Chassis
Software
Assigned
Physically
Assigned
STACK
POSITION
2
3
6
5
4
1
AC
INPUT
1
2
3
ESD
ESD
48VDC CLASS 2
OR LIMITED
PWR SOURCE
48V
A
RTN
A
B
B
A
B
DC FUSES
T4A, MIN. 48V
PWR
A
ALM
FAN
B
OUT
IN
SERIAL
ALM INTF
MCP/1
2
3
MCP/
DSL
MANAGEMENT
10/100 BASE T
STACK
POSITION
2
3
6
5
4
1
AC
INPUT
1
2
3
ESD
ESD
48VDC CLASS 2
OR LIMITED
PWR SOURCE
48V
A
RTN
A
B
B
A
B
DC FUSES
T4A, MIN. 48V
PWR
A
ALM
FAN
B
OUT
IN
SERIAL
ALM INTF
MCP/1
2
3
MCP/
DSL
MANAGEMENT
10/100 BASE T
STACK
POSITION
2
3
6
5
4
1
AC
INPUT
1
2
3
ESD
ESD
48VDC CLASS 2
OR LIMITED
PWR SOURCE
48V
A
RTN
A
B
B
A
B
DC FUSES
T4A, MIN. 48V
PWR
A
ALM
FAN
B
OUT
IN
SERIAL
ALM INTF
MCP/1
2
3
MCP/
DSL
MANAGEMENT
10/100 BASE T
STACK
POSITION
2
3
6
5
4
1
AC
INPUT
1
2
3
ESD
ESD
48VDC CLASS 2
OR LIMITED
PWR SOURCE
48V
A
RTN
A
B
B
A
B
DC FUSES
T4A, MIN. 48V
PWR
A
ALM
FAN
B
OUT
IN
SERIAL
ALM INTF
MCP/1
2
3
MCP/
DSL
MANAGEMENT
10/100 BASE T
STACK
POSITION
2
3
6
5
4
1
AC
INPUT
1
2
3
ESD
ESD
48VDC CLASS 2
OR LIMITED
PWR SOURCE
48V
A
RTN
A
B
B
A
B
DC FUSES
T4A, MIN. 48V
PWR
A
ALM
FAN
B
OUT
IN
SERIAL
ALM INTF
MCP/1
2
3
MCP/
DSL
MANAGEMENT
10/100 BASE T
STACK
POSITION
2
3
6
5
4
1
AC
INPUT
1
2
3
ESD
ESD
48VDC CLASS 2
OR LIMITED
PWR SOURCE
48V
A
RTN
A
B
B
A
B
DC FUSES
T4A, MIN. 48V
PWR
A
ALM
FAN
B
OUT
IN
SERIAL
ALM INTF
MCP/1
2
3
MCP/
DSL
MANAGEMENT
10/100 BASE T
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
3
2
1
5
4
3
8
7
6
17
16
15
14
13
12
11
10
9
2
1
Summary of Contents for HOTWIRE 8610 DSLAM
