Paradyne Hotwire 6211 Command Manual Download

Page: 9 / 50

6211-I1 ADSL2+ Router Command Line Interface User’s Guide

stop

Stops the ADSL connection and the ADSL driver. This command calls BcmAdsl_Uninitialize.

version

Displays the ADSL version

Options

Options for the start and configure commands:

adsl start [--up] [--mod <a|d|l|t|2|p|e|m>] [--lpair <(i)nner|(o)uter>]

[--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>]

or for Annex C:

[--bm <(D)BM|(F)BM>] [--ccw]

adsl configure [--mod <a|d|l|t|2|p|e|m>] [--lpair <(i)nner|(o)uter>]

[--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>]

or for Annex C:

[--bm <(D)BM|(F)BM>] [--ccw]

--up

Calls BcmAdsl_ConnectionStart to start the ADSL PHY connection.

--mod <a|d|l|t|2|p|e|m>

a--all modulations allowed.

d--G.DMT enabled.

l--G.Lite enabled.

t--T1.413 enabled.

2--ADSL2 (G.992.3) enabled.

p--ADSL2+ (G.992.5) enabled.

e--Reach extended ADSL (Annex L) enabled.

m--Double upstream (Annex M) enabled.

•

More than one mode letter can be specified, to enable several modes.

--lpair <(i)nner|(o)uter>

(i)nner--inner loop pair is used.

(o)uter--outer loop pair is used.

--trellis <on|off>

Enables or disables trellis coding.

--snr <snrQ4>

Specifies the Signal-to-Noise Ratio (SNR) margin as the Q4 number.

--bitswap <on|off>

Enables or disables ADSL bitswap

The following options only apply to Annex C:

--bm <(D)BM|(F)BM>

<(D)BM|(F)BM>

(D)BM - DBM mode

(F)BM - FBM mode

Summary of Contents for Hotwire 6211



















































Search results

Summary of Contents for Hotwire 6211

Reviews:

Related manuals for Hotwire 6211

Brands by name

Popular brands

Paradyne Hotwire 6211, Command Manual

Search results

Summary of Contents for Hotwire 6211

Reviews:

Related manuals for Hotwire 6211

Brands by name

Popular brands