Paradyne Hotwire 6211 Command Manual Download

Page: 42 / 50

6211-I1 ADSL2+ Router Command Line Interface User’s Guide

swversion

Name

swversion Displays the current running software version.

Synopsis

swversion show

Description

The swversion command is used to view the software version, ADSL firmware version, and ADSL driver
version.

Examples

Display the current software version.

> swversion show
3.02L.01.A2pB018e.d16f

In this example, 3.02L.01 is the software version, A2pB018e is the ADSL firmware version, and d16f is
the ADSL driver version.

sysinfo

Name

sysinfo

Display the general system information.

Synopsis

sysinfo

Description

The sysinfo command displays the number of processes in the system; system time; system uptime; average
system load in the past 1, 5, and 15 minutes; and system memory consumption. The figures in the memory
consumption table are in 1-kb units.

Commands

None.

Options

None.

Examples

Display the system information.

sysinfo

Summary of Contents for Hotwire 6211



















































Search results

Summary of Contents for Hotwire 6211

Reviews:

Related manuals for Hotwire 6211

Brands by name

Popular brands

Paradyne Hotwire 6211, Command Manual

Search results

Summary of Contents for Hotwire 6211

Reviews:

Related manuals for Hotwire 6211

Brands by name

Popular brands