Paradyne FrameSaver 9620 User Manual Download Page 72

Page: 72 / 79

Maintenance and Troubleshooting

5-18

9621-A2-GB20-30

August 1997

Message

What To Do

What It Indicates

Cause
No.

Quality of service
unavailable

Requested Quality of
Service requested cannot
be provided (e.g.,
throughput cannot be
supported).

No action needed.

Recovery of timer
expired

102

Error-handling procedure
has been initiated as a
result of the expiration of a
timer.

Retry the call.

Requested channel
not available

Circuit or channel
requested cannot be
provided by the other side
of the interface.

Allow the DBM to
automatically call using the
alternate link if Auto
Backup is enabled, or
manually select an
alternate path for the call.

Requested facility
not implemented

Supplemental service
requested is not supported
by this device.

No action needed.

Requested facility
not subscribed

The supplementary service
requested cannot be
provided by the network
until user completes
arrangement with its
supporting networks.

1. Notify your system

administrator that the
arrangements are not
complete.

2. Complete the necessary

arrangements.

Resource
unavailable,
unspecified

No other cause in the
resource unavailable class
applies for this resource
unavailable event.

No action needed.

Response to
STATus ENQuiry

Status enquiry message
received, generating this
message.

No action needed.

Service/option not
implemented

No other cause in the
service or option not
available class applies for
this not implemented event.

No action needed.

Service/option
unavailable,
unspecified

No other cause in the
service or option not
available class applies for
this not available event.

Wait and try again.

Switching
equipment
congestion

Switching equipment
sending the cause is
experiencing heavy traffic.

Wait and try again.

Summary of Contents for FrameSaver 9620
















































































Search results

Summary of Contents for FrameSaver 9620

Reviews:

Related manuals for FrameSaver 9620

Brands by name

Popular brands

Paradyne FrameSaver 9620, User Manual

Search results

Summary of Contents for FrameSaver 9620

Reviews:

Related manuals for FrameSaver 9620

Brands by name

Popular brands