Paradyne FrameSaver 9620 User Manual Download Page 24

Page: 24 / 79

Startup

3-3

9621-A2-GB20-30

August 1997

Procedure

Upon beginning a session, the user interface is blank. To activate:

1. Press Return.

2. One of the following occurs:

I f . . .

Then . . .

What to do now?

Security is disabled

The Main Menu screen
appears.

Begin your session.

Security is enabled

You are prompted for a
login ID and password
(see

Logging In

page 3-1).

Enter your ID and
password. If Invalid
Password appears, see

Device Error Messages

Chapter 5.

Attempting to access the
unit through Telnet and the
user interface is currently
in session

The message Connection
refused: appears.
(FrameSaver access unit
allows only one
connection at a time.)

Attempting direct access
through the COM port and
the user interface is
currently in session

The message User
Interface Already In Use
appears with the active
user’s IP address.

Communication Port and
Login Required
configuration options are
enabled and there is no
contention for the user
interface

The Login screen
appears.

Enter your ID and
password. If Invalid
Password appears, see

Device Error Messages

Chapter 5.

Summary of Contents for FrameSaver 9620
















































































Search results

Summary of Contents for FrameSaver 9620

Reviews:

Related manuals for FrameSaver 9620

Brands by name

Popular brands

Paradyne FrameSaver 9620, User Manual

Search results

Summary of Contents for FrameSaver 9620

Reviews:

Related manuals for FrameSaver 9620

Brands by name

Popular brands