manualshive.com logo in svg

Paradyne 1823, User Manual

Share
Download
Paradyne 1823 User Manual Download Page 30

1823 VoIP Gateway User’s Guide 

5.3.3 DHCP-Lease 

Under the 

DHCP-Lease

 tab, information regarding MAC Address mapping to Lease IP addresses is 

displayed. 

 

 

5.4 Ping

 

To access the Ping screen, click on the 

Ping

 button, which is located under the Advanced menu bar. This 

screen performs the ping test. 

A Ping test is used to verify the status of a network connection after the RIP or static route function is 
enabled. Ping sends a request message to the host and waits for a return message. This function can 
verify if the remote host is reachable. Ping can also measure the round-trip time to the remote host. To 
access the Ping test screen, click on the 

Ping 

tab. Enter the 

Host Name 

or 

IP address 

of the remote 

terminal and click on 

Submit 

to start the ping and display the results.

 

 

 

 

30                                                                              May 2005                                                               1823-A2-GB20-00 

Summary of Contents for 1823


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands