Digiplex DGP-NE96
- 41 -
Programming Guide
Download Memory Key to Control Panel.
1)
Insert the Memory Key (PMC-3) onto the control panel’s connector labelled “
MEM
KEY
”.
2)
To download the contents of the
Memory Key
except
sections
[0001]
to
[0096]
and
[0501]
to
[0532]
, enter installer programming
mode and then enter section
[4010]
.
To download the contents of the Memory Key
including
sections
[0001]
to
[0096]
and
[0501]
to
[0532]
, enter installer programming
mode and then enter section
[4011]
.
3)
When the keypad emits a confirmation beep, remove the Memory Key.
Copy Control Panel to Memory Key
1)
Insert Memory Key (PMC-3) onto the control panel’s connector labelled “
MEM
KEY
”. Ensure the write protect jumper on the memory
key is on.
2)
To copy the contents to the Memory Key
except
sections
[0001]
to
[0096]
and
[0501]
to
[0532]
, enter installer programming mode,
then enter section [4020].
To copy the contents to the Memory Key
including
sections
[0001]
to
[0096]
and
[0501]
to
[0532]
, enter section
[4021]
.
3)
After the confirmation beep, remove the Memory Key. Remove the Memory Key’s jumper if you do not wish to accidentally overwrite
its contents.
Automatic Report Code Programming
When using Contact ID or SIA Reporting formats (section
[3070]
on page 32), default report codes can be programmed automatically. After automatic
defaults are set, they can be changed and the remaining report codes can be set manually.
Software Reset
Performing a software reset will set certain parameters to default values. To do so:
1)
Make sure the
“
RESET
”
jumper (see page 49) on the control panel is ON.
2)
Enter Programming Mode (see page 1).
3)
Enter the 4-digit
[
SECTION
]
corresponding to the software reset you wish to perform:
Section
Description
[4030]
A
LL
R
EPORT
C
ODES
R
ESET
TO
00
Resets all the report codes from sections
[0201]
to
[0296]
,
[0701]
to
[0832]
,
[2001]
to
[2199]
and
[3900]
to
[3999]
to 00.
Sections
[4031]
to
[4037]
reset all the report codes in the following sections to
the default values from the
“Automatic Report Codes List”
[4031]
A
LL
R
EPORT
C
ODES
R
ESET
TO
FF
[
0201]
to
[0296]
,
[0701]
to
[0832]
,
[2001]
to
[2199]
&
[3900]
to
[3999]
[4032]
Z
ONE
A
LARM
/A
LARM
R
ESTORE
AND
Z
ONE
T
AMPER
/T
AMPER
R
ESTORE
R
EPORT
C
ODES
[0201]
to
[0296]
[4033]
U
SER
/K
EYSWITCH
A
RMING
& D
ISARMING
R
EPORT
C
ODES
[
0701]
to
[0832]
, and
[2001]
to
[2199]
[4034]
S
PECIAL
C
ODES
[3900]
to
[3909]
[4035]
S
PECIAL
A
RMING
/D
ISARMING
R
EPORT
C
ODES
[3910]
to
[3929]
[4036]
S
PECIAL
A
LARM
R
EPORT
C
ODES
[3930]
to
[3939]
[4037]
T
ROUBLE
& T
ROUBLE
R
ESTORE
R
EPORT
C
ODES
[3940]
to
[3999]
Section
Description
[4040]
Entering this section will reset all programmable sections from
[0001]
to
[3999]
to factory default values.
[4041]
Entering this section will reset the system master code to 123456.
[4042]
Entering this section will reset all Zone (sections
[0001]
to
[0196]
,
[0201]
to
[0296]
, and sections
[0961]
to
[0984
]) programming to default
values.
[4043]
Entering this section will reset all access control sections from
[2201]
to
[2712]
, excluding door labels, to default values.
[4044]
Entering this section will reset all user code sections from
[1001]
to
[1999]
and
[2001]
to
[2199]
to default values.
[4045]
Entering this section will reset all dialer (sections
[3051]
to
[3081]
) and control panel (sections
[3020]
to
[3043]
, and
[3900]
to
[3991]
)
programming to default values.
[4046]
Entering this section will reset all partition sections from
[3101]
to
[3829]
, excluding partition labels, to default values.
[4047]
Entering this section will reset all PGM (sections from
[0901]
to
[0939]
) and all Keyswitch (sections
[0501]
to
[0632]
) programming, as well
as all Keyswitch arming/disarming report codes (sections from
[0701]
to
[0832]
) to default values.
[4048]
Entering this section will clear all user labels, door labels, partition labels, and zone labels from sections
[0301]
to
[0396]
.
