PaperFolder PH-Knife-14 Manual Download Page 11 | Manualshive

Page: 11 / 19

background image

Page 11

PaperFolder.com

SET TO CREASE

LOADING PAPER

a.

Fan a stack of paper of around 100 sheets.

b.

Load them in the paper tray.

c.

Press the front of the tray down to load the paper.

d.

Move the side guides to be snug with each side of the stack. It should be centered on the
tray. THIS IS VERY IMPORTANT. IF YOU ARE USING THE KNIFE FOLDER, IT WILL NOT PERFORM
PROPERLY IF THE PAPER IS NOT CENTERED.

POWER

Power to the machine can be 110v, 60 hz or 220v, 50 hz. Plug it into a wall circuit with at least 10A
available. DO NOT USE AN EXTENSION CORD.

Plug the electrical cord in and switch on. O is Off. –– is On.

LCD CONTROL PANEL

«
...
9
10
11
12
13
...
»

Summary of Contents for PH-Knife-14




















Reviews:

No comments

Related manuals for PH-Knife-14

Brand: Jack Pages: 7

Brand: Jack Pages: 22

Brand: Pacific Pages: 8

Brand: R+M Suttner Pages: 2

Brand: Janome Pages: 44

EASY TURF TD-01

Brand: We R memory keepers Pages: 20

ELITE GMP C-598

Brand: UNIS Pages: 45

Heavy Duty 1000

Brand: Janome Pages: 72

Brand: Duerkopp Adler Pages: 154

Brand: GBC Pages: 10

Brand: Oki Pages: 653

Brand: Kärcher Pages: 15

memory craft 5700

Brand: Janome Pages: 62

Brand: Truvox Pages: 16

Decor Excel 2 5024

Brand: Janome Pages: 41

Brand: Bally Pages: 444

Brand: Janome Pages: 43

Brand: JUKI Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands