background image

Page 18 

PaperFolder.com

 

CONTROL PANEL 

The control panel does not have to be used in normal operation after you set the speed.  The upper 
button on the left advances the speed in the range 1-9, and the lower button decreases it.  WE 

RECOMMEND THAT YOU USE V7.  If you want to experiment, be careful of going too slow.  The paper 
coming from the PH-14 can back up and jam.   
 
The Red button starts and stops the machine, but the knife folder is controlled by the PH-14.  YOU DO 

NOT HAVE TO SET ANYTHING ON THE KNIFE FOLDER EXCEPT THE SPEED.  Make sure you check it each 
time you run them to make sure they are set fast enough.  V7 is our recommendation.  
 
 
 

 

EMERGENCY STOP 

The big red button on the back right is solely there for an emergency stop.  Push it and it will stop the 
knife folder.  It will not start again until you reset it which means rotating it until it pops back up. 

 
 
 
 

 
 
 
 
 

 
 
 
 

 

 

SET UP THE FOLD ON THE KNIFE FOLDER 

The knife folder is set to fold an 8.5" wide sheet of paper in half. You will need to center your paper in 
the feed tray.  No further setup is required to operate the system.   
 

 

Summary of Contents for PH-Knife-14




















Reviews: