manualshive.com logo in svg

Panoramic Power Energy Insight, Installation And Configuration Manual

Share
Download
Panoramic Power Energy Insight Installation And Configuration Manual Download Page 22

 

 

 

 
 

22 

 

Bridge installation and configuration guide 

January 2018 
© 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD. 
Registered in England & Wales No 3033654

 

3.

 

Connect the USB flash drive to the USB port on the bridge. 

 

4.

 

Boot and wait for the LED self-test sequence to end. Note that this is relevant only if the bridge is not 
yet operational. 

Note 

If you proceed to Step 5 before the self-test sequence ends, the bridge enters configuration mode rather than 
upgrade mode. 

5.

 

If the bridge is connected to the LAN network, 

Disconnect it from the LAN network

.

 

6.

 

Press the 

Configuration

 button for approximately 10 seconds. 

7.

 

The 

 LED lights orange and green. All other LEDs are off. 

8.

 

Wait several minutes for the upgrade process to complete (up to 5 minutes). 

After a successful upgrade the bridge will reboot. The 

 LED lights green, and the bridge returns to 

normal operation. A LED self-test sequence occurs, and the bridge returns to normal operation. 

9.

 

Disconnect the USB flash drive. 

Note 

If the firmware version on the USB drive is identical to the one installed, the bridge will not update, and the 
power LED will turn red. A lower version 

will result in downgrading the bridge’s firmware and a reset of the 

bridge configuration. 

Troubleshooting 

If you encounter a problem, try the solutions listed in this section.  
Otherwise, contact Customer Support for help at 

[email protected]

. 

Problem 

The bridge is not receiving sensor data (the 

 LED is off). 

Solutions 

•

 

Try moving the bridge closer to the electrical panel.  

•

 

Verify the position of the sensors in the electrical panel: make sure they are visible, or t ry 
moving them to the front of the panel. 

•

 

Make sure the RF antenna is tightly screwed into the antenna connector of the bridge. 

•

 

Make sure the bridge is not in configuration mode (the 

LED lights red). 

Summary of Contents for Energy Insight


























Reviews:

No comments

Brands by name

Popular brands

Load more brands