Panduit Atlona AT-HDVS-200-TX Page 9 Manual Download

Page: 9 / 44

AT-HDVS-200-TX / AT-HDVS-200-TX-PSK

HDMI IN 2

RS-232

HDMI

INPUT

DISPLAY

AT-HDVS-200-TX

VOL

HDMI IN 1

VGA IN

AUDIO IN

VGA

RS-232

HDMI IN 2

LAN

HDBaseT OUT

RS-232

HDMI IN 2

RS-232

HDMI

INPUT

DISPLAY

AT-HDVS-200-TX

VOL

HDMI IN 1

VGA IN

AUDIO IN

VGA

RS-232

HDMI IN 2

DC 48V

LAN

HDBaseT OUT

RS-232

9 11

1 INPUT

Press this button to cycle through each of the

available inputs:

HDMI IN 1

HDMI IN 2

, and

VGA

2 VOL (up)

Press this button to adjust the volume on the

connected display. Refer to

Defining the Front-Panel

Buttons (page 14)

for more information.

3 DISPLAY

Press this button to trigger user-defined RS-232/

CEC/IP display control commands. Refer to

Defining

the Front-Panel Buttons (page 14)

for more

information.

4 VOL (down)

Press this button to adjust the volume on the

connected display. Refer to

Defining the Front-Panel

Buttons (page 14)

for more information.

5 HDMI IN 1

Connect an HDMI cable from this port to an HD

source.

6 VGA IN

Connect a VGA cable from this port to a VGA source.

7 VGA

This LED indicator will glow bright green when the

VGA IN port is selected.

8 PW

This LED indicator will glow bright green when the

switcher is powered.

9 AUDIO IN

Connect a 3.5mm mini-stereo audio cable, from an

analog audio source, to this port.

10 HDMI 1

This LED indicator will glow bright green when the

HDMI IN 1

port is selected.

11 HDMI 2

This LED indicator will glow bright green when the

HDMI IN 2

port is selected.

12 FW

Connect a mini USB to USB-A type cable from this

port to a computer to update the firmware.

Refer to

Updating the Firmware (page 37)

for more

information.

13 DC 48V

Connect the power supply to this port to power an

HDBaseT receiver, projector, or other PoE device.

14 RS-232

Connect the included 3-pin Phoenix block from this

connector to an RS-232 control device.

15 HDMI IN 2

Connect an HDMI cable from this port to an HD

source.

16 LAN

Connect an Ethernet cable from this port to the

network.

17 HDBaseT OUT

Use an Ethernet cable to connect an HDBaseT PoE

receiver to this port.

Front

Rear

Panel Description

NOTE:

The

DC 48V

port is only available on

the AT-HDVS-200-TX-PSK.

Summary of Contents for Atlona AT-HDVS-200-TX













































Search results

Summary of Contents for Atlona AT-HDVS-200-TX

Reviews:

Related manuals for Atlona AT-HDVS-200-TX

Brands by name

Popular brands

Panduit Atlona AT-HDVS-200-TX, Manual

Search results

Summary of Contents for Atlona AT-HDVS-200-TX

Reviews:

Related manuals for Atlona AT-HDVS-200-TX

Brands by name

Popular brands