35
34
U S E R MA N UA L
PA N D O R A S MA R T V3
Radio tag
To activate/deactivate service mode, press and hold the
button on a radio tag for 3 seconds (until
the third flash of the LED), release the button.
Phone
Call the system number wait for the answer.
• To activate service mode, dial the
DTMF command and then dial the «Secret PIN-code» from
the Owner’s personal card.
• To deactivate service mode dial the
DTMF command.
Mobile application Pandora Connect
To activate/deactivate service mode, open the mobile application. When the system is online (there
is an Internet or Bluetooth connection), press and hold the
button on the control panel until
the scale is fully loaded.
!
T
o
change
buTTons
layouT
or
add
new
buTTons
on
The
conTrol
panel
,
go
To
«s
eTTings
c
onTrol
buTTons
».
Immobilizer buttons
• To activate service mode, enter the «Immobilizer PIN-code» and press the immobilizer button 10
times within 20 seconds.
• To deactivate service mode, turn on the ignition and enter the «Immobilizer PIN-code».
Service mode indication
• Activated Service mode is indicated by: an icon
in the mobile application, constant green LED when
the ignition is on, long sound signal of a Beeper at the moment you activate the mode.
• Deactivated Service mode is indicated by: no «Service mode» icon
in the mobile application,
no constant green LED when the ignition is on, two long sound signal of a Beeper at the moment
you deactivate the mode.
CONTROL OF THE SYSTEM IN CASE OF EMERGENCY
The system has emergency ways to deactivate security and Anti-hi-Jack functions (using the VALET
button and the «Secret PIN-code») in case of loss or failure of control devices or in case of discharge of a
battery (when you cannot replace it or charge).
Before using emergency system control, check the system and vehicle control devices: check a
battery, turn on a device in accordance with its manual (if required).
If all devices are working, try to make a primary vehicle diagnosis: check the vehicle original control
device, vehicle battery charge level, gearbox selector position, check information on the dashboard.
!
T
he
sysTem
can
be
conTrolled
from
a
phone
using
dTmf
commands
.
0* – Disarming.
998*xxxх – Deactivate authorization devices (Immobilizer and Anti-Hijack functions), where хххх is
the «Secret PIN-code» written on the Owner’s personal card under the protective layer.
1*– Arming.
888* – Activate authorization devices (Immobilizer and Anti-Hi-Jack functions).
!
r
ead
The
procedure
for
enTering
The
pin-
code
before
using
emergency
funcTions
.
ENTERING THE PIN-CODE
The code must be entered only when the base unit is powered and the ignition is off. The PIN-code can
be entered using the external or located on the base unit VALET button. The digits input and correct
input is indicated by the external or located on the base unit LED indicator.
• Enter the first digit • Press the button the number of times equal to the first digit. Pauses between
presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator
flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of the Beeper
confirm the input of the first digit. Then you can enter the next digit.
• Enter the second digit • Press the button the number of times equal to the second digit. Pauses
between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED
indicator flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of
the Beeper confirm the input of the second digit. Then you can enter the next digit.
• Enter the third digit • Press the button the number of times equal to the third digit. Pauses between
presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator
flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of the Beeper
confirm the input of the third digit. Then you can enter the next digit.