Panasonic WX-ST600P Operating Instructions Manual Download Page 39

Page: 39 / 44

Phenomenon

Cause/measure

Reference

page

Audio from the

microphone unit is not

transmitted

●

Is an external device connected to the external

input connector?

When an external device is connected, even

if it is turned OFF, it will take precedence

over the microphone unit, which will stop

audio transmission from the microphone unit.

Disconnect the plug from the external input

connector.

●

Is the volume on the receiver, connected

amplifier, etc. high enough?

Adjust the volume with the volume

adjustment knob.

―

●

Is the status of the product “Not talking”? (Is the

talk indicator red?)

Press the talk button.

15, 16

I cannot talk even

after pressing the talk

button

(The talk indicators

remain off)

●

Has the paired microphone been deleted by the

operations support software?

Pair the microphone again.

●

Is the PTT setting switch set to “PTT ON”?

When set to “PTT ON”, you need to keep

pressing the talk button while talking to

output.

16, 17

I cannot charge the

microphone

(The charge indicator

stays off)

●

Is the microphone properly inserted into the

charger?

Make sure that the microphone is properly

inserted into the charger.

I cannot charge the

microphone

(The charge indicator

only stays on for a few

minutes)

●

Are the batteries already charged?

The batteries may already be fully charged.

Take the microphone out of the charger and

use it as normal.

Summary of Contents for WX-ST600P













































Search results

Summary of Contents for WX-ST600P

Reviews:

Related manuals for WX-ST600P

Brands by name

Popular brands

Panasonic WX-ST600P, Operating Instructions Manual

Search results

Summary of Contents for WX-ST600P

Reviews:

Related manuals for WX-ST600P

Brands by name

Popular brands