8
After completing the adjustment, press the QUIT (F3)
key, then the computer will ask you if you want to save
the current adjustment status.
8
If you want to save, press the Y key, and then press the
ENTER key. Type xxxxxxxx.EV2 CC0 14CA Give an
appropriate file name for xxxxxxxx within 8 letters, but do
not use CS854BE. Then press the ENTER key to finish
the adjustment procedure.
8
If you don't want to save, press the N key, and then press
the ENTER key to finish the adjustment procedure.
4.4 Preset Data Reset Procedure
Note) This adjustment is required when Main Board or
EEPROM (IC5 and IC7) on the Main Board is
replaced.
8
Insert new floppy disk containing DOS Operating System
and the E.V.R. Adjustment Program into IBM PC/AT.
8
At the prompt, type RADJ2 CS85BEPRand press the
ENTER key, then the initial menu page as shown in Fig. 4-
4-1 will be displayed.
Fig. 4-4-1
8
Select the item "1. PRESET DATA RESET" with the
ARROW key and press the ENTER key.
8
When finishing the preset data reset, press the QUIT (F3)
key, then the computer will ask you if you want to save the
current adjustment status.
8
If you want to save, press the Y key, and then press the
ENTER key. Type xxxxxxxx.EV2 CC0 14CA Give an
appropriate file name for xxxxxxxx within 8 letters, but do
not use CS854BE. Then press the ENTER key to finish
the adjustment procedure.
8
If you don't want to save, press the N key, and then press
the ENTER key to finish the adjustment procedure.
Black Line on the Top Plate
Digital Section
(Main Board)
Projection
4.5 CCD Mounting Adjustment
Note) This CCD Mounting Adjustment is required in the
following cases;
1. Replacing the CCD image sensor.
2. Replacing the Sensor Board.
8
The System Controller should be used.
8
Draw the straight cross-line on the surface of the Monitor
Screen as shown in Fig. 4-5-1
Fig. 4-5-1
8
Remove the Camera Head from the Chassis according to
2.1 Disassembling Procedure for the Camera Head.
8
Disconnect the Flexible Cable from CN1 on the Servo
Board.
8
Connect the one end of the Extension Cable
B
to CN1 on
the Servo Board, and connect the other end to CN4 on the
Main Board as shown in Fig. 4-5-2.
Fig. 4-5-2
8
Supply the Power to the WV-CS850B/CS854BE, and the
Camera Head starts panning.
8
After the Camera Head stops panning, mount the Camera
Head on the CCD Mounting Adjustment Jig as shown in
Fig. 4-5-3.
Cross-line
Monitor Screen
Extension Cable
B
Servo Board CN1
Main Board
CN4
Camera
Head
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
M E N U
PANASONIC REMOTE EVR ADJUSTMENT SYSTEM CCTV PRODUCT: CS850 EEPROM: 0
<CONTENTS> RESET
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD(F1)
QUIT(F3)
SAVE(F5)
N T S C
1. PRESET DATA RESET
P a g e ( 1 / 1 )
– 2-18 –
