Panasonic WORKIO DP-150FX Operating Instructions Manual Download Page 63

Page: 63 / 153

Troubleshooting

Starting with:

NOTE

If the printing operation fails, check the following points first:

The printer cable is properly connected.
Length of the printer cable is not longer than 6 ft. (2 m).
Power to the device is turned on.
Paper is loaded on the device properly.
Error message is not displayed on device.

The above points can be verified by printing a test page. Refer to the following for procedures for test
page printing:

Windows 95/98/Me

[General Tab] (See page 14)

Windows NT 4.0

[General Tab] (See page 27)

Windows 2000

[General Tab] (See apge 46)

The status of the devices can be verified by the status monitor.

Summary of Contents for WORKIO DP-150FX


























































































































































Search results

Summary of Contents for WORKIO DP-150FX

Reviews:

Related manuals for WORKIO DP-150FX

Brands by name

Popular brands

Panasonic WORKIO DP-150FX, Operating Instructions Manual

Search results

Summary of Contents for WORKIO DP-150FX

Reviews:

Related manuals for WORKIO DP-150FX

Brands by name

Popular brands