background image

9

5.Replacement Guide

INSTALLATION

10. Insert the other mounting spring into the slot as
       shown and mount grille to fan body. (Fig.10)

9.  Insert  the  sensor  unit  into  slot  of  the  grille
     (position 

① . 

Fix

 

the

 

sensor

 

lead  wire  into  the 

     clasp  (position 

② (

Fig.9)

)

).

Fig.8

Fig.10

Fig.9

8. Insert the grille mounting spring on the wiring 
    side into the slot and insert the plug connector  
    into the housing of the lighting unit.(Fig.8) 

Mount grille carefully so that lead wire of 
sensor unit and lighting unit is not pinched.

Before turn on the light, make sure the
connector at the correct position. If not, the
lighting can’t work.

The claw of connector must latch the rib
completely. (Fig.8)

Ceiling

Grille

Grille

Grille

Ceiling

Clasp

Sensor unit

Gloves

Gloves

Rib

Claw

Insert

lighting unit

lighting unit

Plug connector 

Plug connector 

Mounting spring

Mounting spring

6.  Install  the  night  lamp  and  fluorescent  lamps.
     (Fig.6)

7.  Install  light  kit  cover  assembly.  (Fig.7)

3

Fig.6

Fig.7

Secure  screw
(M4X8)

CAUTION

CAUTION

Fluorescent
lamp

Night lamp

Light kit cover 
assembly

Summary of Contents for WhisperSense FV-08VQCL5












Reviews: