11
10
1. Check the Surrounding Area
z
Check that there is nothing behind the unit.
x
Check that there is enough room to recline the unit.
• In the interests of safety, the unit may stop moving if it hits
something while reclining.
2. Check the Unit
z
Lift up the pillow and the center cushion to check
that there are no rips in the fabric of the back
cushion, etc.
x
Check that the power plug has not been damaged
or has pins or dust sticking to it.
AFTER CHECKING THE SURROUNDING AREA, TURN ON THE POWER
BEFORE USING THE UNIT
Do not leave
anything here.
16in.
(40cm)
16in.
(40cm)
Main Cushion Fabric
Check
3. Turn the Power On
z
Plug the power plug into the power socket.
x
Turn the lock switch to the “open” position.
c
Turn on the power switch on the back of the unit.
When plugging the unit in, make sure that there is at least 4in.
(10cm) slack in the power cord.
(Take care to ensure that the power cord is not caught by the
unit when it reclines.)
2
3
1
on
off
lock
open
lock switch
1. After Carrying Out Safety Checks, Turn the Unit On (See Page 11)
z
Plug the power plug into the power socket.
x
Turn the lock switch to the “open” position.
c
Turn on the power switch on the back of the unit.
• Please always check for the following before using the unit.
- Check that there is no person, pets, or obstacles around the unit.
- Check that there are no rips in the fabric.
2. Press button.
• When you press
button, the Programmed Operation and Leg Massage
Buttons will flash. If the cover of the controller is open, then the Manual Operation Selection Buttons will flash.
3. Select the Desired Program or the Desired Movement on the Manual Operation
(See details on page 14)
Programmed Operation
• Ideal for people who feel tired all over.
• Ideal for people who want to operate the massage lounger simply.
z
Select the required program.
x
Press the Neck/Shoulder or Lower Back Buttons if you want to focus on a particular area.
c
The chair will recline to the optimum angle for the massage. The massage will then begin
and continue until the end of the selected program is reached, at which time the massage
will automatically stop. An average program massage is 15-17 minutes.
Manual Operation
• Used for selecting a particular massage movement or area to be massaged.
• Ideal for people who want to adjust movement and location during the course of a massage.
• Ideal for people who want just a little more on the shoulders at the end of their massage.
z
Open the cover of the controller and select the massage required.
x
The seat will automatically recline to the optimum massage position.
c
Adjust the position and intensity of the massage rollers.
v
Press
button
to complete the massage.
4. Adjust the Angle of the Backrest and Legrest (See Page 13)
• Adjust the angle of the backrest and legrest to the most comfortable position.
• When retracting the backrest, as the massage heads must be retracted in the interests
of safety there may be a slight delay before the backrest actually starts to retract.
Please continue to hold down the Reclining Button until the backrest is fully retracted.
5. Turn the Power Off to Finish the Massage
(See Page 20)
z
Turn the power switch to the “off” position.
x
Turn the lock switch the “lock” position.
c
Unplug the power cord.
• Here you will find an overview of how to use the massage lounger. Please refer to the pages shown for further details.
HOW TO USE THE MASSAGE LOUNGER — INTRODUCTION
2
3
1
on
off
lock
open
lock switch
3
2
1
on
off
lock
open
lock switch
If excessive pressure is applied to the massage heads during upper body massage, in the interests
of safety the massage heads may stop moving. If this occurs, raise your body slightly before
restarting it. (This may happen more frequently for people with a weight of 220 lbs. or more.)
If the massage mechanism stops (or if all markings and buttons on the controller start to flash), turn
off the power switch, wait for approximately 10 seconds, and then turn the power switch on again.
After each use
• Be sure to tum the power switch to “off”.
• To prevent children from using this unit, lock the power switch by moving the
operating lock switch to the “lock” position.
• As a further precaution, unplug the power cord from the outlet after each use.
NOTE:
Be careful not to pinch the cord under the leg frames of the chair or any other objects.
NOTE:
The operating lock
switch prevents the unit
from being turned on
when switch is in the
“lock” position.
All manuals and user guides at all-guides.com
