background image

Slide #60

10 Blinks Error Code (Full HD Models) Flowchart

Leave SS11 and SS33 unplugged. Remove 

connectors SC2, SC20 on the SC board. Then 

plug in the TV and press the power switch

Unplug the TV and remove connectors SS11 and SS33 from 

the SS board. Plug in the TV and press the power switch

Does the TV 

power up and

stay on?

No

Yes

Note: 

If the TV does not turn on at all, unplug 

it and leave it unplugged for 3 minutes.

Replace

the SS board

(See Note 2)

Did the 

number of 

blinks 

change?

No

Yes

Replace

the SC board

Unplug the TV and reconnect 

connectors SC2, SC20, SS11, 

and SS33. (Follow the SU/SD 

boards isolation procedure shown 

on slides 17~19). Plug in the TV 

and press the power switch

Does the 

TV power 

up and

stay on?

No

Yes

Unplug the TV and reconnect connectors 
SS11, SS33, SC2, and SC20. Plug in the 

TV and press the power switch

No

Yes

Replace

the P board

LIST OF MODELS

TC-P42S1

TC-P42G10

TC-P42U1

TC-P42U1

TC-42PS14

TC-P46S1

TC-P46G10

TC-P46U1

TC-P50S1

TC-P50G10

TC-P50U1

TC-P50V10

TC-50PS14

TC-P54S1

TC-54G10

6 blinks

10 Blinks

Replace

the A board

Disconnect the TV and 

unplug connector A1. Plug 

in the TV. Ground pin 8 of 

connector A1 momentarily. 

Yes

No

Does the 

TV power 

up and

stay on?

Replace

the K board

Any 

other 

blinking 

code

Replace

the A board

Note 2: 

If the SS or SC board 

fail repeatedly with shorted Vsus, 

replace the A board also. 

Is there 

15V at pin 7 of  

connector P6 at 

the moment

the relay 

clicks ?

Start Here

The SU or/and the SD Boards  can be

defective. Follow procedure on

slides 17~21 to determine which

of the 2 boards is defective.

No

If the power LED continues to blink even after the TV is unplugged, press and hold the power 
switch on the TV for a few seconds until the LED turns off.

Summary of Contents for Viera TC-P42X1








































































Reviews: