Panasonic Viera TC-P42X1 Revised Troubleshooting Handbook Download Page 13

Page: 13 / 71

Slide #13

Power LED’s Response to Connectors Removal (42” HD Models)

Model:

TC-P42X1

Connector

Result

A20

Unplugged

A31

Unplugged

SOS 6 Blinks

A32

Unplugged

SOS 6 Blinks

A20

Unplugged

A31

Unplugged

A20

Unplugged

A32

Unplugged

A31

Unplugged

A32

Unplugged

SOS 6 Blinks

A20

Unplugged

A31

Unplugged

A32

Unplugged

TV Stays On With Black Screen

HD Models

Do not remove any connectors from any of

the PC boards unless instructed to do so.

CAUTION:

Some steps require

removal of connectors and

sometimes PC boards removal.

Do not let the TV run for more

than 30 seconds while

connectors or boards are

disconnected.

CAUTION:

The TV power should not be

turned on while SC2 is disconnected. This

could damage the SS board.

Summary of Contents for Viera TC-P42X1








































































Search results

Summary of Contents for Viera TC-P42X1

Reviews:

Related manuals for Viera TC-P42X1

Brands by name

Popular brands

Panasonic Viera TC-P42X1, Revised Troubleshooting Handbook

Search results

Summary of Contents for Viera TC-P42X1

Reviews:

Related manuals for Viera TC-P42X1

Brands by name

Popular brands