Panasonic Viera TC-P42X1 Revised Troubleshooting Handbook Download | Manualshive

Page: 47 / 71

background image

Slide #47

Board

Result

SU

OK

SD

OK

SC

OK

Board

Result

SU

Bad

SD

OK

SC

OK

Board

Result

SU

OK

SD

Bad

SC

OK

Board

Result

SU

OK

SD

OK

SC

Bad

Board

Result

SU

Bad

SD

Bad

SC

OK

Board

Result

SU

Bad

SD

OK

SC

Bad

Board

Result

SU

OK

SD

Bad

SC

Bad

Board

Result

SU

Bad

SD

Bad

SC

Bad

A

B

C

D

A

B

C

D

Follow this procedure if the SU
board and/or the SD board are
bad while the SC board measures
OK

Follow this procedure if the SU
board and/or the SD board are
bad while the SC board is also
bad

Follow this
procedure if
only the SC
board is bad

Follow this
procedure
when all 3
boards check
OK

Replace the

SU, SD, and

SC boards

Replace the SC

board.

Go to the

next slide

Go to the

Slide #16

1.

Remove the front cabinet and check for cracks and blown pixels. (For front cabinet removal procedure go to slide 24).

2.

Check the ICs on the SU and SD boards for blown hole on the surface. (Go to slide 25 to see pictures)

3.

Perform the SU, SD, and SC boards resistance test procedure shown on slides 26~31. Match the result with one of the
following boxes (A~D) and follow the instructions at the bottom of the page.

Start Here

7 Blinks Error Code (2 of 4)

If the power LED continues to blink even after the TV is unplugged, press and hold the power
switch on the TV for a few seconds until the LED turns off.

«
...
45
46
47
48
49
...
»

Summary of Contents for Viera TC-P42X1








































































Reviews:

No comments

Related manuals for Viera TC-P42X1

HTX25S31, HTX29S31S, HTX34S31

Brand: Haier Pages: 21

Brand: Panasonic Pages: 88

TC-32LX85 Operating Manual (English

Brand: Panasonic Pages: 50

Brand: Panasonic Pages: 104

Brand: Panasonic Pages: 84

Brand: Samsung Pages: 160

Brand: Panasonic Pages: 27

Brand: Coby Pages: 1

ST 72-3202/7 TOP

Brand: Grundig Pages: 8

Brand: Linsar Pages: 38

Brand: Saba Pages: 13

Brand: Uniteck Pages: 22

Brand: Insignia Pages: 62

Brand: Sansui Pages: 25

Easy Home HD TOPBOX

Brand: Best Buy Pages: 160

Brand: Symphonic Pages: 4

Brand: Sandstrom Pages: 12

Brand: Salora Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands