background image

Slide #34

2 Blinks Error Code (All Models)

No

Yes

Reconnect P25 and measure the 
resistance between pin 1 of 
connector P6 and ground (Chassis)

Is there a 

short 

circuit?

Unplug the TV and check the resistance between pin 1 of connector P6 and ground (Chassis)

Is there a 

short 

circuit?

Yes

No

Plug in the TV and turn it on. Measure 
the voltage at pin 1 of connector P6

Is there 

15V 

present?

No

Yes

Replace

The P board

Replace

The A board

Unplug connectors P6, P11, and P25 on the P 
board. Measure the resistance between pin 1 of 
connector P6 and ground (Chassis) 

Is there a 

short 

circuit?

No

Yes

Replace

The P board

Reconnect P11 and measure the 
resistance between pin 1 of 
connector P6 and ground (Chassis)

Is there a 

short 

circuit?

No

Yes

Replace

The SS board

Disconnect SC20 on the SC board 
and measure the resistance between 
pin 1 of connector P6 and ground 
(Chassis

Replace

The A board

Is there a 

short 

circuit?

No

Yes

Replace

The A board

Replace

The SC board

If the power LED continues to blink even after the TV is unplugged, press and hold the power 
switch on the TV for a few seconds until the LED turns off.

Start Here

Summary of Contents for Viera TC-P42X1








































































Reviews: