Panasonic VB-44210G User Manual Download | Manualshive

Page: 261 / 394

background image

Section 700 - Operation

Chapter 6. SLT Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

6-5

calls are routed to the extension defined in permanent call forwarding.

The following types of incoming trunk calls follow permanent call forward
settings:

- Direct trunk calls (including DID/DNIS)

- Transferred trunk calls.

• When an Absence Message is set on a DID extension, incoming DID calls

are routed according to the ringing assignment programmed for the
incoming trunk.

Busy Override

(All Versions)

Description

Extensions in the same Paging Group (1-7) can break into one another’s
outside calls or intercom calls to relay information or to create three-party
Conference Calls.

Operation

Press “4” when you hear the busy tone.

An alert tone is issued at both phones.

Related Programming

• FF1 (System): Alert Tone for Busy Override & OHVA

• FF1 (System): Extension Class of Service Setting (CPC-AII and CPC-B

Version 3.1 or higher)

• FF3 (Extension): Extension Class of Service Assignment (CPC-AII and

CPC-B Version 3.1 or higher)

• FF3 (Extension): Busy Override Send

• FF3 (Extension): Busy Override Receive

• FF3 (Extension): Extension Page Group

«
...
259
260
261
262
263
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Samsung Pages: 2

Brand: Easiphone Pages: 13

Brand: Earthworks Audio Pages: 3

FINISH-OUT MC111M

Brand: M&S Systems Pages: 2

EXI5560 - EXI 5560 Cordless Extension...

Brand: Uniden Pages: 48

Brand: Panasonic Pages: 88

Berkshire 400 Plus

Brand: ATL Product Pages: 4

Brand: Coby Pages: 1

Dialog 4106 Basic

Brand: Aastra Pages: 35

Brand: Premier Pages: 12

Brand: Vicon Pages: 14

Brand: Alcatel Pages: 2

3100 ICP - 4.0 L

Brand: Mitel Pages: 18

Brand: Net2Phone Pages: 20

Brand: Sagem Pages: 170

Brand: Armstrong Pages: 2

Brand: Swisscom Pages: 110

Brand: JVC Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands