Panasonic TC-PXXGT30 Technical Manual Download

Page: 79 / 83

Quick Procedure To Check For Short or Low Resistance Condition of

the Vda Line

Make sure the TV is disconnected.

Remove any residual charge from the Vda line by momentarily grounding them through a 500 ohms
resistor (At least 5Watts).

Measure the resistance between chassis ground and the pins indicated on the table below. A dead
short or a reading lower than 1K indicates a shorted or partially shorted line.

Vda

is generated by the Power supply and is only used by the Panel (Panel Drive ICs)

Test points for the Vda can be easily found on the P board. To check for short circuit or low resistance on
this line, follow this procedure:

Preparation

Voltage Test Points

Connector

Pin Number

Voltage

P35

Vda

Slide 79

Summary of Contents for TC-PXXGT30




















































































Search results

Summary of Contents for TC-PXXGT30

Reviews:

Related manuals for TC-PXXGT30

Brands by name

Popular brands

Panasonic TC-PXXGT30, Technical Manual

Search results

Summary of Contents for TC-PXXGT30

Reviews:

Related manuals for TC-PXXGT30

Brands by name

Popular brands