Panasonic TC-PXXGT30 Technical Manual Download

Page: 51 / 83

Troubleshooting 7 Blinks Failures (GT and VT Series)

Note: Perform firmware upgrade after replacing the SC board or the SS board

Follow the procedure on the

previous slide

to check the Vsus, and Vda for short circuit or low resistance reading.

Is there a short

circuit of the

Vsus or Vda,?

Yes

Start Here

Shorted

Vda

Shorted

Vsus

Continue on

next slide (A)

Continue on

next slide (B)

Unplug connectors P2 and P11, on the P board. Measure the
resistance between pin 1 of connector P2 and ground (Chassis)

Measure the resistance between pin1

of connector SC2 on the SC board

and ground (Chassis).

Yes

Is there a

short

circuit?

Replace the P

board

Yes

Is there a

short

circuit?

Measure the resistance between

pin1 of connector SS11 on the

SS board and ground (Chassis).

Yes

Is there a

short

circuit?

Replace the

SC board

Replace the
SS and the
SC boards

Replace the

Unplug the TV and

disconnect SC20 on

the SC board. Turn

the power on

How many

times is the

power LED

blinking?

Replace

The A board

7 Blinks

8 Blinks

Slide 51

Summary of Contents for TC-PXXGT30




















































































Search results

Summary of Contents for TC-PXXGT30

Reviews:

Related manuals for TC-PXXGT30

Brands by name

Popular brands

Panasonic TC-PXXGT30, Technical Manual

Search results

Summary of Contents for TC-PXXGT30

Reviews:

Related manuals for TC-PXXGT30

Brands by name

Popular brands