Panasonic TC-PXXGT30 Technical Manual Download

Page: 39 / 83

Troubleshooting Solid Red LED Failure (Locked Mode)

Blink

Code

List of boards likely to cause this symptom.

Main Suspect

Solid Red

SC - SS

Yes

Check connections between connector P6 on the P board and A6 on the A board. If the problem persists, unplug the TV and disconnect SC20, SS33,

and C10/C20. Reconnect the TV and turn the power on. Then, after the power LED turns on, press the power switch again to turn the TV off.

Did the

TV turn

off?

Start Here

Unplug the TV and reconnect it.

Turn the power on and measure the

voltage on pin 10 of connector P6.

Replace the P

board

Power LED stays on

Is there 15V

present?

Replace the A

board.

Unplug the TV and reconnect

SC20 and C10/C20 only

(See

Note1

before reconnecting

C10/C20).

Turn the power on.

Then, after the power LED turns

on, press the power switch again

to turn the TV off.

Yes

Did the TV

turn off?

Replace the SC

board

Yes

Replace the SS

board

To confirm that the TV is on Locked Mode, 1

, press the power switch to turn on the TV, then when the LED turns on, press the power switch to turn

the TV off. If the LED stays on, the TV is on Locked Mode but if the LED goes off, then the symptom is different (Like no video or black screen).

New

Note 1

: Remove

connector P35 from

the P board before

reconnecting C10/C20.

Then reinstall P35

after C10/C20 is

reconnected.

Slide 39

Summary of Contents for TC-PXXGT30




















































































Search results

Summary of Contents for TC-PXXGT30

Reviews:

Related manuals for TC-PXXGT30

Brands by name

Popular brands

Panasonic TC-PXXGT30, Technical Manual

Search results

Summary of Contents for TC-PXXGT30

Reviews:

Related manuals for TC-PXXGT30

Brands by name

Popular brands