44
45
Advanced
Network Setting
Network Setting
This is a setting for connecting to a broadband environment.
■
Press to exit from
a menu screen
■
Press to return
to the previous
screen
Display menu
Select “Setup”
Menu
Picture
Audio
Timer
Lock
VIERA Link
SD card
Closed caption
Setup
select
set or next
Select “Network setting”
Setup
2/2
Advanced setup
About
Reset to defaults
VIERA Link settings
Network setting
VIERA CAST setting
Network Cameras list
ECO/energy saving
select
Select the item and adjust
Network setting
2/2
MAC address
12-34-56-78-80-ab
LAN speed setting
Automatic
LAN speed
10BASE half duplex
Software update
Network setting
1/2
Connection test
Succeeded
IP setting mode
Automatic
IP address
192.168.0.5
Subnet mask
255.255.255.0
Default gateway
192.168.0.254
DNS setting mode
OK
Primary DNS
192.168.0.20
Automatic
Secondary DNS
192.168.0.21
select
adjust
The network settings become effective when you close the menu and run “Connection test”.
Connection
test
Check that the network settings are as shown below, and then start “Connection test”.
Select “Connection test” and press OK.
Succeeded: “Connection test” succeeded
Only home network:
Home
network
is
available.
Failed:
Check the broadband environment connection
and settings and the network settings, and then
perform the test again.
Test in progress
---: Test not yet performed
*Press OK again to cancel the test.
(It takes a while to cancel the test.)
Network setting
1/2
Connection test
Succeeded
IP setting mode
Manual
IP address
192.168.0.5
Subnet mask
255.255.255.0
Default gateway
192.168.0.254
select
ok
IP setting
•
IP setting
mode
•
IP address
•
Subnet mask
•
Default
gateway
Select “IP setting mode” and set to “Automatic”.
■
Manual setting
Select “IP setting mode” and set to “Manual”
Select the item and press OK
Check the specifications of the broadband router and
enter each IP address.
(When IP automatic acquisition in DHCP can be used)
Network setting
1/2
Connection test
Succeeded
IP setting mode
Automatic
IP address
192.168.0.5
Subnet mask
255.255.255.0
Default gateway
192.168.0.254
The acquired address is displayed.
select
ok
Subnet mask
OK
10I
0
.
0 .
0 .
0
change
channel
ok
or
Each IP address is acquired automatically.
DNS setting
•
DNS setting
mode
•
Primary DNS
•
Secondary
DNS
Select “DNS setting mode” and set to “Automatic”.
(When DNS automatic acquisition in DHCP can be used)
Network setting
1/2
Connection test
Succeeded
IP setting mode
Automatic
Default gateway
192.168.0.254
DNS setting mode
OK
Primary DNS
192.168.0.20
Automatic
Secondary DNS
192.168.0.21
The acquired address is displayed.
select
ok
Each IP address is acquired automatically.
If you are using a broadband router, IP automatic
acquisition in DHCP can be used under normal
circumstances. If you are not sure, check with the
person who installed the equipment, or check the
instructions for each device.
■
Manual setting
Select “DNS setting mode” and set to “Manual”
Select the item and press OK
Enter each IP address as was specified by the
provider.
Primary DNS
10I
0
.
0 .
0 .
0
select
ok
or
Connection
speed
setting
•
LAN speed
setting
•
LAN speed
Select “LAN speed setting” (Default is “Automatic”)
Normally, select “Automatic”.
If “Connection test” failed, set the “LAN speed setting”
to “manual” and then select “10BASE half duplex”,
“10BASE duplex”, “100BASE half duplex” or “100 BASE
duplex”.
Cannot be selected when the “LAN speed setting” is
“Automatic”.
Changing the settings may make it impossible to
connect some types of equipment.
Network setting
2/2
MAC address
12-34-56-78-80-ab
LAN speed setting
Automatic
LAN speed
10BASE half duplex
Software update
select
adjust
Software
update
Select “Software update”
Press OK to start the software update screen.
Follow directions of the screen.
* Set “Clock” first. (p. 18)
Network setting
2/2
OK
MAC address
12-34-56-78-80-ab
LAN speed setting
Automatic
LAN speed
10BASE half duplex
Software update
select
ok
