Panasonic T-Mobile KX-HDV130 Administrator'S Manual Download Page 76 | Manualshive

Page: 76 / 332

background image

Value Range

•

Registered: The unit has been registered to the SIP server, and the
line can be used.

•

Registering: The unit is being registered to the SIP server, and the
line cannot be used.

•

Blank: The line has not been leased, the unit has not been
configured yet, or a SIP authentication failure has occurred.

Note

•

Immediately after starting up the unit, the phone numbers of the
lines will be displayed, but the status of the line may not be
displayed because the unit is still being registered to the SIP
server. To display the status, wait about 30 to 60 seconds, and
then click

[Refresh]

to obtain updated status information.

4.3 Network

This section provides detailed descriptions about all the settings classified under the

[Network]

tab.

4.3.1 Basic Network Settings

This screen allows you to change basic network settings such as whether to use a DHCP server, and the IP
address of the unit.

Note

•

Changes to the settings on this screen are applied when the message "Complete" appears after clicking

[Save]

. Because the IP address of the unit will probably be changed if you change these settings, you

will not be able to continue using the Web user interface. To continue configuring the unit from the Web
user interface, log in to the Web user interface again after confirming the newly assigned IP address
of the unit using the phone user interface. In addition, if the IP address of the PC from which you try to
access the Web user interface has been changed, close the Web port once by selecting "

Off

" for

76

Administrator Guide

Document Version 2015-12

4.3.1 Basic Network Settings

«
...
74
75
76
77
78
...
»

Summary of Contents for T-Mobile KX-HDV130













































































































































































































































































































































Reviews:

No comments

Related manuals for T-Mobile KX-HDV130

KXDT346 - DIGITAL PROPRIETARY TELEPHONE

Brand: Panasonic Pages: 2

Brand: Samsung Pages: 108

Dialog 4422 IP Office

Brand: Aastra Pages: 151

Brand: Aastra Pages: 2

Dialog 4420 IP Basic

Brand: Aastra Pages: 74

Brand: Aastra Pages: 101

Clearspan 6739i

Brand: Aastra Pages: 9

Clearspan 6739i

Brand: Aastra Pages: 8

Clearspan 6739i

Brand: Aastra Pages: 20

Brand: Aastra Pages: 104

Brand: Aastra Pages: 108

Clearspan 6731i

Brand: Aastra Pages: 2

Brand: Aastra Pages: 7

Brand: Aastra Pages: 1140

Brand: Aastra Pages: 174

Brand: Aastra Pages: 888

Dialog 5446 IP Premium

Brand: Aastra Pages: 87

Brand: Sagem Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands