17
TQBJ0987
The device is connected, but audio cannot be
heard through this unit.
≥
For some built-in Bluetooth
®
devices, you have to set the audio
output to “SC-HC402” or “SC-HC400” manually. Read the
operating instructions for the device for details.
The sound is interrupted.
≥
The device is out of the 10 m communication range. Place the
Bluetooth
®
device closer to this unit.
≥
Remove any interference between this unit and the device.
≥
Other devices that use the 2.4 GHz frequency band, such as
wireless routers, microwaves, cordless phones, etc. are
interfering. Place the Bluetooth
®
device closer to this unit and
distance it from the other devices.
≥
Select “MODE 1” for stable communication. (
l
8)
The following messages or service numbers may
appear on the unit’s display.
“--:--”
≥
You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (
l
14).
“ADJUST CLOCK”
≥
Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
≥
Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
≥
The unit has been left unused for about 20 minutes and will shut
down within a minute. Press any button to cancel it.
“ERROR”
≥
Incorrect operation is performed. Read the instructions and try
again.
“F
” / “F
” (“
” stands for a number.)
≥
There is a problem with this unit.
Disconnect the AC mains lead from the AC outlet, reconnect it to
the outlet after about 30 seconds. Wait for about 10 seconds, then
turn on the unit. If the problem still persists, disconnect the AC
mains lead and consult your dealer.
“ILLEGAL OPEN”
≥
Sliding door is in the wrong position. After turning off the unit,
disconnect the AC mains lead from the AC outlet, reconnect it to
the outlet after about 30 seconds. Wait for about 10 seconds, then
turn on the unit. If the message is still displayed, disconnect the
AC mains lead and consult your dealer.
“LINKING”
≥
This system is trying to connect to the last connected Bluetooth
®
device when “BLUETOOTH” is selected.
“NO DEVICE”
≥
The USB device is not inserted correctly. Read the instructions
and try again (
l
7).
“NO DISC”
≥
Insert the disc to be played (
l
7).
“NO PLAY”
≥
Examine the content. You can only play supported format. (
l
19)
≥
The files in the USB device can be corrupted. Format the USB
device and try again.
≥
The unit may have a problem. Turn the unit off and then on again.
“NO PRESET” (
[HC402]
)
≥
There are no preset DAB/DAB+ stations to select. Preset some
channels. (
l
11)
“NO SIGNAL” (
[HC402]
)
≥
This station cannot be received. Check your antenna (
l
6).
“NOT SUPPORTED”
≥
You have connected an unsupported USB device.
“PGM FULL”
≥
The number of programmed tracks is more than 24.
“PLAYERROR”
≥
You played an unsupported file. The system will skip that track
and play the next one.
“READING”
≥
The unit is checking the “CD”/“USB” information. After this display
has disappeared, start operating.
“REMOTE
” (“
” stands for a number.)
≥
The remote control and this unit are using different codes. Change
the code on the remote control.
– When “REMOTE 1” is displayed, press and hold [OK] and [1]
for at least 4 seconds.
– When “REMOTE 2” is displayed, press and hold [OK] and [2] for at
least 4 seconds.
“SCAN FAILED” (
[HC402]
)
≥
Stations are not receivable. Check your antenna and try Auto
scanning (
l
11).
If “SCAN FAILED” is still displayed find the best signal reception
with the “MANUAL SCAN” tuning function. (
l
12)
“SOUND
NOT SET” (“
” stands for a number.)
≥
There is no saved setting under the selected sound setting
number. Save the sound settings. (
l
14)
“USB OVER CURRENT ERROR”
≥
The USB device is drawing too much power. Select a source other
than “USB”, remove the USB and turn the unit off.
“VBR”
≥
The system cannot show the remaining play time for variable bit
rate (VBR) tracks.
“WAIT”
≥
This is displayed, for example, when this unit is turning off.
Messages
SC-HC400_402-EGEBGN~TQBJ0987.book 17 ページ ２０１７年３月１６日 木曜日 午後７時５２分
