1
1
2
2
Attachment Screw
(M6
#
16)
Allen Key
9
Allen Key
Attachment Screw
(M6
#
10)
Allen Key
Use This Screw
#
6
Use This Screw
#
2
Use This Screw
#
4
ASSEMBLY
Attaching the Armrests (On Both Right and Left Sides)
Connecting the Air Plugs (On Both Right and Left Sides)
Attaching the Control Panel Stand to the Right or Left Armrest
1. Insert the armrest into the unit.
• Markings indicating left-hand and right-hand
sides can be found on the inside surface of
each armrest.
• Make sure the control panel cord does not
become pinched when fitting the right armrest
onto the unit.
2. Fasten the armrest with the
attachment screws.
• Set the three attachment screws in place first
and then tighten them firmly.
1. Decide which side to attach the
control panel stand to.
2. Fasten the control panel stand with
the attachment screws in four places.
• Set the four attachment screws in place first
and then tighten them firmly.
1. Insert the air plug.
• Push on the air plug until you hear it click into
place.
2. Place the plug cover over top of the
air plug and fasten with the screw.
Use the mark as
a guide for insertion.
Attachment Screw
(M5
#
16)
Plug Cover
Air Plug
• Diagram shows attachment to right armrest.
Turn screws clockwise
to tighten.
1
2
1
2
8
Ensure there is adequate space for reclining.
Mat
Handle
Place your fingers in the groove.
Legrest
Rubber
Section
Area where legrest
could touch floor.
Area where unit touches floor.
Keep at least
4" (10 cm)
away from
wall, etc.
Keep at least
4" (10 cm)
away from
wall, etc.
Mat
Approx. 14"
(35 cm)
Approx. 77" (195 cm)
Width approx. 27" (68 cm)
(approx. 33" (84 cm) with
armrests attached)
Approx. 12"
(30 cm)
Front
Back
Connector Hose
Air Plug
(Cross-section)
BEFORE USING THE UNIT
SETTING UP THE MASSAGE LOUNGER
After Removing Everything from the Box, You Should Have the Following
Where to Use the Unit
Armrests
Marks indicating left and right can be found
on the underside of each armrest.
Pillow
Control Panel Stand
Attachment Screws (M6
#
16) — 6
Left Armrest — 3
Right Armrest — 3
Control Panel Stand Attachment Screws
(M6
#
10) — 4
Plug Cover Attachment Screws
(M5
#
16) — 2
Plug Covers — 2
Allen Key — 1
Control Panel
Stand Covers
Lock Switch Keys — 2
Massage Lounger
Accessories
Small holes on the inside
fabric are an intentional part
of the functional design.
CAUTION
• Do not use the unit in areas with high humidity,
such as the bathroom, etc. as this can lead to
electric shock or other accidents.
• Place the unit on a totally flat surface.
Failure to do so may result in the seat tipping over.
• Do not use the massage lounger in direct sunlight or in
places where it will be exposed to high temperatures,
such as in front of a heater, etc., as this can cause
discoloration or hardening of the synthetic leather.
• Place the unit on a mat to prevent floor damage.
• When placing a mat under the unit, the size of the mat
should be sufficient (at least 47
#
28 in. (120
#
70 cm)) to
cover the areas where the unit touches and the legrest
could touch the floor, as shown in the diagram on the left.
Move the chair by having one person hold onto the rubber
section on the underside of the legrest and another person
use the handle on the back of the backrest.
Carrying in the Unit
CAUTION
• Make certain the legrest has been retracted fully
to its original length.
Failure to observe this safeguard could result in injury
due to the legrest returning to its original length
when the unit is being moved.
• Use care to prevent pinching of hands or feet when letting
go of the legrest as its mechanism will cause it to slam shut.
• Use care to prevent lower back and other injuries that
could occur when lifting this heavy object (approx. 179
lbs (81 k
g
)).
0.2"
(4 mm)
Clip