3. Extend mode (EXT OPTION menu)
This projector has extend mode "EXT OPTION" menu in addition to standard on-screen menus.
This mode has Self-Check function, Test Pattern and other functions for Service.
3. 1. Procedure to open / close "EXT OPTION" menu.
1. When the projector is power ON, press "POWER" button on the main unit or remote control unit to display
"POWER OFF" confirmation screen.
2. Press the "
" button to select "CANCEL" in the "POWER OFF" confirmation screen.
3. On the main unit or remote control unit, press the buttons in order of "
▲
", "
▼
", "
▲
", "
▼
" and "ENTER".
4. When "MENU" button is pressed at the "EXT OPTION" mode, Extend-mode is closed.
3. 2. EXT OPTION Menu and Functions
1.FAN FULLMODE
・
Setting the cooling fan motor rotation speed.
2.AUTO SETUP
・
Setting AUTO SETUP mode.
- NORMAL: Dot clock is adjusted strictly.
- SPECIAL: Dot clock is adjusted roughly.
* Do not usually change initial setting (NORMAL).
3.SELF CHECK
・
The content of self checking are displayed.
(1) -
Software Version (MM : Main microprocessor, F:FPGA )
* FPGA (Field Programmable Gate Array)
(2) -
Input signal Display
( [NO-SYNC] is displayed when there is no input signal).
(3) -
Input Horizontal/Vertical signal frequency
(For the RGB/YPBPR Input only)
(4) -
The temperature abnormality check
("NG" is displayed for any abnormality)
(5) -
Temperature around the air intake port/exhaust port and
Filter sensor
(deg C/A/D conversion value)
(6) -
Filter sensor Difference Correction (A/D conversion) Value
(7) -
Rotation check of Intake fan / Lamp fan / Iris fan
(Displays "NG" when Fan is abnormal condition)
(8) -
Iris condition check (Abnormal condition = "NG")
(9) -
Lamp condition check (Abnormal condition = "NG")
(10) -
Lamp cover installation check (Abnormal condition="NG")
(11) -
Displays the projector cumulative usage time
(12) -
Cumulative usage time (actual time) and Number of
LAMP ON times
"Current number : Last reset : Reset of last but one"
(13)-
Displays the serial number of the projector.
(14)-
Software Version (SM : Sub microprocessor, IM : IRIS control microcomputer)
(15)-
Gamma, Color Unevenness and Crosstalk correction data check (Whether data are stored in the flash ROM)
(16)-
Thermo sensor (Intake Air / Exhaust Air / Filter Air) measurement value when thermal shutdown
(deg C/A/D conversion value)
Switching ON "FAN FULLMODE", the rotation level of the
fan becomes high-speed rotation (fixed). Moreover, when
"FAN FULLMODE" is ON, changing "HIGH ALTITUDE
MODE" in OPTION menu becomes impossible (setting
FAN FULLMODE is given priority more than HIGH
ALTITUDE MODE).
SELF CHECK S/N SD12345678
MM:1.00 SM:1.00
F:1.00 IM:1.00
XGA60 G-SAVED OK
H 48.48KHZ U-SAVED OK
V 60.60HZ C-SAVED OK
----------- TEMP ------------
TEMP OK
INTK 22.7/157 INTK ---.-/---
EXST 26.6/148 EXST ---.-/---
FLTR 88.7/094 FLTR ---.-/---
FLTR SENSOR OFFSET 79
----------- FAN -------------
INTK OK EXST OK
LAMP OK PWR OK
IRIS OK
-------- MECHANICAL ---------
IRIS OK LENS MEM OK
----------- LAMP ------------
LAMP OK 4000H OK
COVER OK
------- UNIT HISTORY --------
TOTAL 11H RESET 0
12H10 52 12H10
0H00 0 0H00
0H00 0 0H00
EXT OPTION
FAN FULL MODE
OFF
AUTO SETUP
NORMAL
SELF CHECK
STATUS
FLICKER ADJUST
1.
2.
3.
4.
5.
(1)
(2)
(3)
(4)
(5)
(6)
(8)
(7)
(9)
(11)
(10)
(12)
(13)
(14)
(15)
(16)
(17)
(19)
(18)
(20)
(21)
"OK" display becomes red characters when shutting
down because abnormality happened time.
INF - 6
Summary of Contents for PT_AT6000E
