Panasonic PT-VW350 Operating Instructions Manual Download Page 98

Page: 98 / 119

Lamp and Warning Indicators

When an indicator lights up

If a problem should occur inside the projector, the lamp indicator <LAMP> and the warning indicator <WARNING> will inform

you by lighting or blinking. Check the status of the indicators and remedy the indicated problems as follows.

Attention

Before you take a remedial measure, follow the procedure of switching the power off indicated in “Powering Off the

projector”. (

page 39)

Lamp indicator

Indicator

Lighting in

red.

Blinking

in red.

Status

Time to replace the lamp unit.

A problem is detected in the lamp or the power supply for the

lamp.

Check

Was [REPLACE LAMP] displayed when

you turned on the power?

The indicator lights up when the

runtime of the lamp unit has reached

5 000

hours (when [LAMP POWER] is

set to [NORMAL]).

Have you turned on the

power again immediately

after turning it off?

Some error has occurred in

the lamp circuit.

Check for

fluctuation (or drop) in the

source voltage.

Remedy

Replace the lamp unit.

Wait a while until the

luminous lamp cools off,

and then turn on the power.

Turn off the projector, and

unplug the AC power cord,

and consult your dealer.

Note

If the lamp indicator <LAMP> is still lighting or blinking after taking the preceding measures, ask your dealer for repair.

Warning indicator

Indicator

Lighting in red.

Blinking

in red.

Blinking in red. (Slow)

Status

Internal temperature

high (warning).

Internal temperature

high

(standby status).

The projector detects an

abnormal condition and

cannot be turned on.

Check

Is the air intake/exhaust port blocked?

Is the room temperature high?

Is the air filter unit dirty?

Remedy

Remove any objects that are blocking the air intake

exhaust port.

Install the projector in a location with an ambient temperature of 0 °C

(32 °F) to 40 °C (104 °F).

Do not use the projector at high altitudes of 2 700 m (8 858

) or higher

above sea level.

Replace the air filter unit. (

page 99)

If the projector is turned off

again, unplug the AC power

cord and contact the dealer

or the service center for

service and checkup.

Note

If the warning indicator <WARNING> is still lighting or blinking after taking the preceding measures, ask your dealer for

repair.

Lamp indicator <LAMP>

Warning indicator <WARNING>

98 -

ENGLISH

Chapter 5 Maintenance - Lamp and Warning Indicators

Summary of Contents for PT-VW350
























































































































Search results

Summary of Contents for PT-VW350

Reviews:

Brands by name

Popular brands

Panasonic PT-VW350, Operating Instructions Manual

Search results

Summary of Contents for PT-VW350

Reviews:

Brands by name

Popular brands