[SHUT DOWN]
The countdown timer is displayed after 30 seconds without input signal. The projection lamp is turned off and cooled
down when reached the set time, then the projector enter into standby status.
[OFF]
Power management function is off.
[READY]
The countdown timer is displayed after 30 seconds without input signal. The projection lamp turns off and cools
down when reaching the set time, meanwhile the projector is in the power management mode.
The projection lamp will be turned on if the input signal is reconnected or any button is pressed.
Setting [TIMER]
The timer can be set to 5-120 minutes. The increment is 5 minutes.
1) Press
as
to select [TIMER].
2) Press
qw
to set the timer (5-120
MIN
.).
f
The time will switch each time you press the button.
Note
f
The factory default setting for [TIMER] is [15 MIN.].
Setting [STANDBY MODE] in step 3)
Set the
operation mode
during standby.
The default setting is [ECO] that keeps power consumption low during standby. When
the network function or the serial communication function is used during standby, set to [NORMAL].
1) Press
as
to select [STANDBY MODE].
2) Press
qw
to switch the item.
f
The items will switch each time you press the button.
[ECO]
Select this item to reduce power consumption during standby.
[NORMAL]
Select this item to use the network function or the serial communication function during standby.
[NETWORK]
Select this item to reduce power consumption during standby, and to operate the projector via the wired LAN or the
serial communication function by using the Wake on LAN function.
Note
f
If [STANDBY MODE] is set to [ECO], you cannot use network functions when the projector is standing by. Also, you cannot
use some RS-232C protocol commands.
f
When set to [ECO], it may take approx. 10 seconds longer before the projector starts projecting after the power is turned on,
compared with when [NORMAL] is set.
f
If [STANDBY MODE] is set to [NETWORK], it takes less power consumption than it is set to [NORMAL].
f
When [STANDBY MODE] is set to [NETWORK], it will be no restriction for network function and serial communication
function within 60 seconds when the Wake on LAN function is working.
f
The setting of [STANDBY MODE] cannot be returned to the factory default even if the [PROJECTOR SETUP] menu →
[INITIALIZE ALL] is executed (
x
page 75).
[EMULATE]
When controlling the projector on a computer via the <SERIAL IN> terminal, set use of control commands on a previously
purchased Panasonic projector. This allows the control software for an existing Panasonic projector to be inherited and used.
1) Press
as
to select [EMULATE].
2) Press the <ENTER> button.
f
The [EMULATE] screen is displayed.
3) Press
as
to select one item.
[DEFAULT]
VW350 series, VX420 series, VZ575N series, VW535N series, VX605N series, EZ580 series, EW640 series,
EX610 series, EW540 series, EZ770 series, EW730 series, EX800 series, VW345N series, VX415N series,
VW340Z, VX410Z, VX42Z, RZ475 series, RZ470 series, RW430 series, RZ370 series, RW330 series
[D3500]
D3500 series
[D4000]
D4000 series
[D/W5k SERIES]
D5700 series, DW5100 series, D5600 series, DW5000 series, D5500 series
[D/W/Z6k SERIES]
DZ770 series, DW740 series, DX810 series, DZ680 series, DW640 series, DX610 series, DW730 series,
DX800 series, DZ6710 series, DZ6700 series, DW6300 series, D6000 series, D5000 series, DZ570 series,
DW530 series, DX500 series
[L730 SERIES]
L730 series, L720 series, L520 series
[L780 SERIES]
L780 series, L750 series
[L735 SERIES]
L735 series
[L785 SERIES]
L785 series
[F/W SERIES]
FW430 series, FX400 series, FW300 series, F300 series, F200 series, FW100 series, F100 series
[LZ370]
LZ370 series
[LB/W SERIES]
LB3 series, LB2 series, LB1 series, ST10 series, LB90 series, LW80NT series, LB80 series, LB78 series, LB75 series
72 -
ENGLISH
Chapter 4 Settings - [PROJECTOR SETUP] menu
