Panasonic PT-RZ475EA Operating Instructions Manual Download Page 125

Page: 125 / 142

Chapter 5

Maintenance — Troubleshooting

ENGLISH - 125

Problems

Points to be checked

Page

3D function is not working.

Are the [3D INPUT FORMAT] and [3D MODE] settings of [3D SETTINGS] correct?

Check the 3D eyewear settings.

―

Is a 3D signal which is supported by the projector being input?

135

Is the [LIGHT POWER] setting in [ECO MANAGEMENT] set to [ECO2]?

Left and right images are

reversed (not showing

properly).

Are the devices synchronized? Check the 3D eyewear settings.

―

Change the [LEFT/RIGHT SWAP] setting of [3D SETTINGS].

Image in the 3D eyewear

flickers.

Are you within the reception range? Are there any obstructions between the 3D

eyewear and the IR transmitter? (when using VESA standard 3D eyewear)

―

3D eyewear is not

functioning.

Are batteries of the 3D eyewear drained? If you use the rechargeable 3D eyewear,

charge it. If you use the battery-powered 3D eyewear, replace the battery.

―

Is the IR transmitter connected properly? (when using VESA standard 3D eyewear)

―

Turn off the projector and turn it on again. (when using VESA standard 3D eyewear)

―

Is the [3D MODE] setting of [3D SETTINGS] correct?

Attention

If problems persist even after checking the preceding points, consult your dealer.

Summary of Contents for PT-RZ475EA















































































































































Search results

Summary of Contents for PT-RZ475EA

Reviews:

Brands by name

Popular brands

Panasonic PT-RZ475EA, Operating Instructions Manual

Search results

Summary of Contents for PT-RZ475EA

Reviews:

Brands by name

Popular brands