background image

- 5 -

SAFETY PRECAUTIONS

IMPORTANT SAFEGUARDS

1. 

Read Instructions - 

All the safety and operating  instructions

should be read before the unit is operated.

2. 

Retain Instructions -

 The safety and operating  instructions

should be retained for future reference.

3. 

Heed Warnings -

 All warnings on the unit and in the

operating instructions should be adhered to.

4. 

Follow Instructions - 

All operating and user instructions

should be followed.

5. 

Electrical Connections -

 Only a qualified electrician should

make electrical connections.

6. 

Attachments -

 Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7. 

Cable Runs -

 All cable runs must be within permissible

    distance.

8. 

 Mounting -

 This unit must be properly and securely mounted

   to a supporting structure capable of sustaining the weight

   of the unit.  Accordingly:

a. The installation should be made by a qualified service

person, and should conform to all local codes.

b. Care should be exercised to select suitable hardware

to install the unit, taking into account both the

composition of the mounting surface and the weight of

the  unit. Be sure to periodically examine the unit and the

supporting structure to make sure that the integrity of the

installation is intact.  Failure to comply with the foregoing

could result in the unit separating from the support

structure and falling, with resultant damages or injury to

anyone or anything struck by the falling unit.

UNPACKING

Unpack carefully.  Electronic components can be

damaged if improperly handled or dropped.  If an item

appears to have been damaged in shipment, replace it

properly in its carton and notify the shipper.

Be sure to save:

1. The shipping carton and packaging material.  They are the

safest material in which to make future shipments of the

equipment.

2. These Installation and Operating Instructions.

SERVICE

       For service on Panasonic/Videolarm equipment contact:

Panasonic Technical Center

54 West Gude Dr.

Rockville  MD   20850-1150

Phone:  301-762-5125

Fax:  301-251-0347

1-800-528-6747

9:00 AM - 5:00 PM EASTERN TIME

CAUTION:  TO REDUCE THE RISK OF

ELECTRICAL SHOCK, DO NOT EXPOSE

COMPONENTS TO WATER OR MOISTURE.

The lightning flash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

"dangerous voltage" within the product's

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

PANASONIC TECHNICAL SUPPORT

CAUTION

RISK OF

ELECTRIC SHOCK!

!

!

Summary of Contents for PCF2






Reviews: